A thermistor is placed in a 200°C environment and its resistance measured as 30000Q. The material constant B is 3627°K. If the thermistor is then used to measure a particular temperature and its resistance is measured as 6002. The thermistor temperature in °C. Select one: O a. 573 O b. 255 C. 692.64 d. 965.64

A thermistor is placed in a 200°C environment and its resistance measured as 30000Q. The material constant B is 3627°K. If the thermistor is then used to measure a particular temperature and its resistance is measured as 6002. The thermistor temperature in °C. Select one: O a. 573 O b. 255 C. 692.64 d. 965.64

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
Diodes Are Connected In Series To Share A Total... 21 Question • Two diodes are connected in series to share a total reverse voltage of VD=D 5 KV. Reverse leakage currents of the diodes are ID1=30 mA and Ip2=35 mA. - Find Vp1 and Vp2 for R,=R2=100 k2 - Find R, and R2 for VD1=VD2 R1 VD1 Hint: Is=L,+IRj= I,2+IR2 VD R2 VD2
ciocle with 24mA OF Current Flowing through has a vortage chop of 0.75V. Determine the reverse Saturation Current Is In A. Assume M = 1. Present Using ^ Cxy to answer in scientific notation your For the exponent. A H
In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for source voltage V1 and resistor R3 resistance as in the circuit schematic. V1 -15V R3 2700 D1 1N753A RL Determine the lowest possible value for the load RL, so that the voltage drop across it is equal to the Zener voltage. For your diode, use model Zener 1N753A. This diode has a Zener voltage of 6.2V, a Zener current of 60mA, a Zener impedence of 72, and a test current of 20mA.
A three-phase rectifier is supplied by a 173.2-V rms line-to-line 60-Hz source. The RL load is a 100 resistor in series with a 15-mH inductor. Determine THD taking Is1 = 1.35
Half-wave rectifier loaded with R-L is fed with a 120 VAA 60 Hz source. 10 Ω loadFind the inductance value that limits the average load current to 5A for the resistance.
What are the states for diodes in the figure below? D1 D2 4 k2 10 V 10 V O a. D1 off D2 on O b. D1 off D2 off O c. D1 on D2 off O d. D1 on D2 on
Q*: Calculate the current through 48 Q resistor in the circuit shown in Figure(i).Assume the diodes to be of silicon and forward resistance of each diode is 1 Q. D D2 48 2 ww 10 V= D4 D3 (i)
a. If you do not go completely around the loop when applying Kirchhoff’s voltage law, then the algebraic sum of the voltages cannot be determined the algebraic sum of the voltages will always be positive the algebraic sum of the voltages will always be negative the algebraic sum is the voltage between the start and finish points b. A p -type semiconductor is a semiconductor doped with impurity atoms whose electron valence is +4 pentavalent impurity atoms trivalent impurity atoms
liting Q9. For the circuit shown in Figure C9, Calculate the following i) Current through the Silicon diode (Isi). ii) Current through the Resistor R2 (1). iii) Current through the diode D4 (IGe4). iv) Voltage at points V3 and V4. Is D1. D2 Si Si oV4 RI 1.3K2 R3 2.7K R2 3K2 IGe4| 15V D5 Si 03 D4 Ge Ge V2 1V Figure C9
Q2: Draw the output waveform for the three shown circuits. 1- R1 +10V 10 kn D2 V 0- 5V 5 V -10V Diodes are IN914. 2- Assume Vm=20V, show the Vdc on the graph D2 3- Assume VM318V and V=5V. 34
How temperature effect conductivity? Explain with the help of following equation. m e'n7'