A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the ultimate strength.

A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the ultimate strength.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 69 % - Percentage of Reduction in Area = 39 % - Final length after fracture = 35.5 mm - Final Diameter after fracture = 3.6 mm & - Ultimate stress = 396 MPa SOLUTION: iv) Initial Diameter (in mm) = v) Ultimate Load (in N) =
Problem: A tensile test specimen of stainless steel alloy having a with a diameter of 12.6 mm and a 50 mm gage length was tested to fracture. Load and deformation data obtained during the test are given: Determine: (a) the modulus of elasticity. (b) the proportional limit. Load (kN) 0.00 Change in length (mm) (c) the ultimate strength. 0.00 (d) the yield strength (0.20% offset). 0.00 25.79 0.00 (e) the fracture stress. 0.05 51.59 0.10 (f) the true fracture stress if the final diameter 66.55 73.36 80.18 87.77 0.20 of the specimen at the location of the fracture 0.30 0.45 was 8.89 mm 0.63 95.35 0.81 101.42 105.98 112.05 1.01 1,18 1.41 only solve d, e,f 118.13 123.46 128.03 131.85 133.39 134.95 135.73 1.66 1.94 2.27 2.60 2,82 3.15 3.35 3.68 136.53 136.56 3.93 135.84 4.26 135.14 4,66 133.66 4.94 130.67 5.22 5.47 128.44 124.69 5.70 120.92 5.82 117.91 5.95 fracture 116.52
The yield stress for mild steel is 207MP.. A specimen with diameter of 0.01lm and length of 0.1m is subjected to a load of weight of 10kg, and the resulting elongation is 6.077 microns. Determine whether the stress is above or below the yield stress, and if it is below, compute the Young's modulus of the material.
A structural component in the form of a wide plate is to be made of a steel alloy that has a fracture toughness of 77 MPa.m ¹/2 and a yield stress of 1400 MPa. Inspection of the plate has identified an internal through the thickness crack of length 7.7 mm. Assume a value of Y=1. What is the maximum stress the component should be subjected to in order to not undergo rapid fracture.
A metallic rod with an initial diameter of 10 mm and an initial length of 50 mm is subjected to the tensile test. After the fracture, the final length was measured as 51.8 mm, and the final diameter was measured as 9.5 mm.(a) Calculate modulus of elasticity, ultimate tensile strength, elongation at fracture in %,reduction of area in %, true stress at maximum load, true strain at maximum load, strain hardening exponent, strength coefficient.?
A steel rod specimen with a diameter of 200mm was subjected to a force 5000 N in the stress-strain experiment, if the area of the rod at fracture was 25434 mm^2, determine the percentage of the sample ductility (RA).
A mild steel tensile specimen of initial length 44 mm and initial diameter 6.4 mm is subjected to a tensile test and the following data are obtained. - Yield Strength as 88 MPa - Maximum Strength as 212 MPa - Fracture Strength as 152 MPa - Percentage of Elongation as 63 % - Percentage of Reduction in area as 39% Determine the Final length, Final area, Yield load, Ultimate load
For a steel element with a 0.2% steel characteristic, a stress test was applied and the analysis of the data thrown by the material is required in terms of a variation of force and the respective deformations. Determine the following: A.Determine the percentage elongation at the point where the part develops the fracture. B.Construct the “Stress-Strain” diagram C.Maximum tensile strength of the part.
Qu2. (A) What is fatigue? Mention the sequence of steps involved in fatigue of a smooth specimen. Mention Four (4) factors that affect fatigue of smooth specimens, stating how each affects fatigue life (B) A very wide panel made of a material of plane-strain fracture toughness of Kic=55MPaVm was found to have a central crack of size 2.5mm. It is subjected to cyclic loading at a design (or working) stress of 690MPA and stress ratio of zero. (a) Sketch the stress-time graph of the loading cycle and determine (i) Stress Range, (ii) maximum cycle stress, (iii) stress amplitude and (iv) mean stress (b) Will the initial loading cycle cause the panel to fracture? Why or whynot? Compute the maximum allowable fatigue flaw size that can fracture the panel during the cyclic loading. (Assume that plain strain condition prevails). (c)
1 Q 4 N Current Attempt in Progress 30¹ F1 A specimen of a 4340 steel alloy with a plane strain fracture toughness of 54.8 MPa m (50 ksi vin.) is exposed to a stress of 978.0 MPa (141800 psi). Assume that the parameter Y has a value of 1.18. - Your answer is partially correct. @ 2 (a) If the largest surface crack is 0.9 mm (0.03543 in.) long, determine the critical stress o. i 1608.13 (b) Will this specimen experience fracture? W S Yes v eTextbook and Media Hint Save for Later 38 command F2 # 3 E D 80 F3 X C $ 4 R MPa 000 000 F4 F % 5 V F5 T G 6 B MacBook Pro Y H & 44 N U 8 J Attempts: 1 of 5 used en l M 9 K DD F9 0 < H I -O L Submit Answer A F10 P V . t C F11 { command option [ + " = ? |