A tensile force of 1.5kN produce an elastic reduction in diameter of 3.6 x 104 mm on a metal alloy specimen that has a diameter of 6.5 mm. Detemine: 1. The modulus of elasticity of the alloy (Unit: GPa) 2. The Poisson's ratio of this alloy

A tensile force of 1.5kN produce an elastic reduction in diameter of 3.6 x 104 mm on a metal alloy specimen that has a diameter of 6.5 mm. Detemine: 1. The modulus of elasticity of the alloy (Unit: GPa) 2. The Poisson's ratio of this alloy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: Detarmine Ix, ÎIy= O for shaded area in Red Glour. %3D

A: We will split the shape as follows

Q: 1008 A stone is thrown vertically upward from the gre t per sec. One second later another stone is…

A: Given Velocity of stone 1 = 48.3 ft/s Stone 2 = 96.6 ft/s Find Distance, h

Q: In performing his favorite workout routine, Jason throws a ball with an initial velocity of 12.3 m/s…

Q: (b) the height of he building

A: For solution refer below images.

Q: The diameter of the cylinder in a scrap baling press is 150 mm. The stroke of the cylinder is 2.5…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Why do we need to double the dimension up if we use slope?

A: Given: A beam subjected to two loads and moment To find: Reactions

Q: Find to the nearer thousandth inch the circumference of the ring that fitsaround this piston for a…

A: Given Diameter, d = 0.8 in

Q: Compute the displacement done in object so that work done is said to be 124.55 J If force applied is…

Q: Ten and one-half foot-pounds of work is required to compress a spring 2 inches from its natural…

A: Given data Work = 10+1/2 (lb-ft) Initial compression = 2in Find the work required to compress the…

Q: w The pipe assembly in (Figure 1) is secured on the wall by the two brackets. Figure ◄ Previous 60 4…

A: According to the question Weight of the pot W=75lb We need to find a moment of the due to the pot…

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: How much change in the power of wind will take place if wind velocity becomes 3 times and blade…

A: To determine the change in power of the wind if the velocity of the wind becomes 3 times and length…

Q: An engine turns at 250 revolutions per minute and its stroke is 450 mm. Find the average piston…

A: Step 1: (1). Average Piston Speed: The formula for the average piston speed is: Average Piston…

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

Q: Calculate the impulse due to the force. a. 10 kg-m/s b. 20 kg-m/s c. 5 N-s d. 15 N-s

A: Compute the impulse due to the given force.

Q: (x(x+ y) = y(x – y) By homogenous equation solve %3D

A: DE1 (3x2y + 2xy + y3)dx + (x2 +y2)dy = 0 so, M = (3x2y +2xy +y3) and N = (x2 +y2) dMdy=3x2 + 2x…

Q: Question 3 Determine the no of revolertions bearing rototing at the rate 2 yns done by 6ohz in it it…

A: No. of revolution by bearing in 1 sec = 60

Q: Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to…

A: Considering a frictionless seesaw mechanical system. Mechanical Advantage of the system is the ratio…

Q: Design the biggest box (volume) without cover that made from 6m² of aluminum. Hint: Use Lagrange…

A: Objective - designing the biggest box (volume) possible made up of area of 6 m2 .

Q: H.W2: two large plate surfaces are 2.4cm. the space between the surface if filled glycerine.what…

Q: ..Shakespeare write Hamlet? а. did b. was С. had d. is

A: Given Fill in the blanks To find Appropriate word suitable for the question

Q: The impeller of a radial pump with a diameter of 34.2 is shaped in such a way that its head is cut…

A: Given Data: The initial diameter of the pump, d1=34.2 Initial head, h1 Final head, h2=0.5h1

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at a distance of 14th of its…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find Mean effective pressure Indicated Power

Q: Rc is -178.25 Ib. Why in the formula it's 17825 ?

A: The value of RC is represented as : Rc=-178,25 =-17825 lb The negative sign denote the direction…

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: why are you squaring the velocity in the eq

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: why have you writen the answers in mm. when all the length are in meters

Q: For questions 4)r Calculate the velocity of Block B, after collision. can tutor use m1u1 + m2u2 =…

Q: The punching machine is using the flywheel for its smooth running operation. The flywheel running at…

A: Given data: Convert the “rps” into “rpm” as follows:

Q: Probles No. 2 A Ball is dropped and takes O.47 seconds to travel past a Mindow 3.50 netera tall.…

Q: 2 Find T: For q=-KA when dr

Q: What is the velocity of car in m/min, when it is travelling with 35 km /hr.

A: Given data: - The velocity of car in (km /hr) is v = 35 km/hr.

Q: A transmission shaft used to transmit power of 55 kW. During transmission shaft is subjected to a 30…

A: Given data: The power transmitted by the shaft is P = 55 kW. The torque acting on the shaft is T =…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

Solve this early both parts

A tensile force of 1.5kN produce an elastic reduction in diameter of 3.6 x
104 mm on a metal alloy specimen that has a diameter of 6.5 mm.
Detemine:
1. The modulus of elasticity of the alloy (Unit: GPa)
2. The Poisson's ratio of this alloy

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum how long was the seesaw on Joe's side?
Draw a circular hole of 2cm deep and give dimensions to it.
A company has a contract to build a sewer in a nearby province, it must dig a ditch 2m wide, 1m deep, and 2000m long. Laborers are available at P 120/day for an 8-hr day work and can dig at an average of 0.5 cu-m per hr. A ditchadigging machine maybe rented at a cost of P 1,500 a day for all the time it is in use or in transit. One day would be required for transporting the machine one way. Freight cost would total P 4,000. The machine operator would be paid P350/day including travel time for two days. If the machine is used, three laborers are needed. The ditch digging machine can excavate 1 cu-m in 6 min. All workers and machine rentals must be paid on full 8-hr a day basis. What would you recommend and by how much it must cost?
Resolve and draw the diagram of all internal efforts.
A of the velocity in m/s of point B. - OB
The displacement of a piston in cubic inch with a cylinder bore of 7.62-cm and the stroke is 3-in.
Compute the displacement done in object so that work done is said to be 124.55 J If force applied is 30 N
Q3/ including setting the machine, a worker manufactures 79 pieces of different tools in 7 hours and 15 minutes. If the standard time for the tool was Setting time = 40 min Production time per tool= 10 min Compute: 1-The standard time for manufacturing the 79 tools 2-Efficiency of operator
In a manufacturing process, a drill press automatically drills a hole into a sheet metal part on a conveyor. In the drilling operation the drill bit starts at rest direcdly above the part, descends quickly, drills a hole, and quickly returns to the start position. The maximum vertical speed of the drill bit is 4 in./s, and while drilling the hole, it must move no more than 2.6 in./s to avoid warping the metal. Let s(t) be the drill biť's height (in inches) above the part as a function of time t in seconds. Sketch possible graphs of the drill bit's velocity [s'(t)] and acceleration [s"(t)].
_% od 25m is 9m
Given the table of results find the following. Give answers in KW. Please show all working out Rate of heat transfer to evaporator from the chilled water Rate of heat transfer from condenser to the cooling water Rate of heat transfer to refrigerant in Evaporator using enthalpy values Rate of heat transfer from refrigerant in Condenser using enthalpy values Work input from the compressor to the refrigerant using enthalpy values
Please solve part B only