The yield stress for mild steel is 207MP.. A specimen with diameter of 0.01lm and length of 0.1m is subjected to a load of weight of 10kg, and the resulting elongation is 6.077 microns. Determine whether the stress is above or below the yield stress, and if it is below, compute the Young's modulus of the material.

The yield stress for mild steel is 207MP.. A specimen with diameter of 0.01lm and length of 0.1m is subjected to a load of weight of 10kg, and the resulting elongation is 6.077 microns. Determine whether the stress is above or below the yield stress, and if it is below, compute the Young's modulus of the material.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A straight bar of uniform cross section is tested in tension. The bar’s cross sectional are is 6.5 square centimeter and a length of 4m. when the tensile load reaches 85kN, the total elongation is 2.5mm What is the stress and the modulus of elasticity of the bar
A steel Column is 10m long and Ø1.2m. It carries a load of 102MN. Given the modulus of Elasticity is 256GPA. Find the stress, Strain, and determine how much the column is compressed. Label the following diagram to show Stress, Strain, Tensile Strength, Yield Strength and Rupture Strength
A solid truncated cone is subject to an axial force P as shown. The exact elongation is d = PL/ (2pc²E). Replace the cone by n equal thickness circular cylinders and derive the expression as a function of n, P, L, C, E. draw a graph showing variation in elongation d with respect to n values. Take n from 1 to 100. Given that the P = 1 kip, L = 12 inch, C= 4 inch, E = 30x10° psi. B 2c
A mild steel rod of 12mm diameter was tested for tensile strength with the gauge length of 60mm. After the test final length and the final diameter were 80mm and 7mm, respectively. Find the strain in the transverse direction
Stress strain behavior of a cast iron with a diameter of 15.8mm and gauge length of 60.80mm is shown in the graphs. Find the ductility in percent elongation
The plate shown below initially measures 90 X 65mm . Find the changes to these dimensions when subjected to the stresses shown. The modulus of elasticity of the material is 214 E GPA and poissons ratio is 0.32. Also derive the expressions for the change in dimensions of a cube subjected to three dimensional loading.
A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress acting on the bar?
Find the tensile stress in the rod having a diameter of 25 mm subjected to a tensile load of 500 N. If Young's modulus of the material is 200 GPa, what is the strain in the rod?
A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load of 38,000 lb. The corresponding gage length = 3.0103 in (neglect the 0.2 percent yield point). The maximum load of 54,000 lb is reached at a gage length = 3.453 in. Determine the modulus of elasticity (neglect the 0.2% offset, and round to the nearest whole Msi). 37
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulusE=120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F.
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm diameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) :