A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G 28 GPa, and the region BC is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60-mm outside diameter and 30-mm inside diameter. Determine the maximum shearing stress in the aluminium in MPa if a torsional load of 4000 N-m is applied at B. Ends A and C are rigidly clamped. 45 mm 0 mm 30mm

A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G 28 GPa, and the region BC is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60-mm outside diameter and 30-mm inside diameter. Determine the maximum shearing stress in the aluminium in MPa if a torsional load of 4000 N-m is applied at B. Ends A and C are rigidly clamped. 45 mm 0 mm 30mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E, = 10000 ksi] alloy. The length of segment (1) is L, = 70 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 98 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of 8z = 2100 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B Сорer Answer: in. AL = i
The normal stress at point A equals to The shearing stress at point A equals to 400 mm 200 mm 2kN 1kN - 20 mm Section a-a
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
Solid mech.
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 1) What is the deformation 8Ag in mm? 10KN 0.8m 0.4m 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D What is the axial stress o Ag in Pa? 10KN 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
A Analyse the beam shown by the method of Consistent deformation
STRAIN
Problem 4 For the shown structure, AB is made by A-36 steel (Est = 200GPA, ast = 12 x 10-67 °C) and BC is made by %| 73.1GPA, aal = 23 × 10-6/ °C). Both AB and BC are having circular cross sectional area. The aluminum (Eal gap between C and the rigid wall at D is initially 0.15 mm. For the following situations, find (1) reaction forces at fixed end A and D (2) Plot the axial load diagram P=400 kN applied at B and there is no temperature -0.15 тm 600 mm 600 mm vi. change vii. P=400 kN applied and temperature in both AB and BC 25°C segments had dropped AT P=400 kN applied, however, the temperature in AB increased ATst = 25°C and temperature in BC decreased ATal = 25°C vii. B. 25 mm 50 mm