A stem power plant operates with high pressure of 5.5 MPa, and has boiler exit temperature of 450 °C. The condenser is at a temperature of 45 °C. All the components are ideal except for the turbine, which has an exit state quality x=97%. Determine: (a) The efficiency of the turbine (b) The heat transfer in the condenser (kg/kg) (c) The heat transfer in the boiler (ki/kg)

A stem power plant operates with high pressure of 5.5 MPa, and has boiler exit temperature of 450 °C. The condenser is at a temperature of 45 °C. All the components are ideal except for the turbine, which has an exit state quality x=97%. Determine: (a) The efficiency of the turbine (b) The heat transfer in the condenser (kg/kg) (c) The heat transfer in the boiler (ki/kg)

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 20RQ: Welded ______sealed compressors are normally used in household refrigerators.

See similar textbooks

Similar questions

Condensers in these refrigerators are all_______cooled.
The enthalpy entering the turbine of a geothermal power plant is 2750 KJ/kg and ,ass rate of 1 Kg/sec. The turbine brake power is 1000 KW condenser outlet has enthalpy of 210 KJ/kg. If temperature rise of cooling water in condenser is 8, what is the mass of cooling water requirement?
Task (4) Critically compare how the changes of the heat transfer efficiency will affect the lifetime of the turbine.
Q.3 A. Calculate the thermal efficiency of a Rankine cycle in which the steam is initially dry saturated at 2 Mpa and the condenser pressure 75 kN / m². Express this efficiency as a percentage of a Carnot cycle efficiency of the same limits of temperature. B. If the steam leaves the boiler at 350 ° C with the same pressure of the boiler and condenser given above. Explain why the Rankine efficiency in (A) is less than in (B), and why the ratio of efficiencies of the respective Rankine and Carnot is greater.
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
There are received 68,000 kg/h of steam by an ideal regenerated engine, having onlyone heater, of which the heater receives 15,400 kg/hr the condenser receives theremainder at 0.007 MPa. If the heater pressure is 0.96 MPa, find the state (quality or̊SH) of the steam (a) at the heater entrance and (b) at the condenser entrance.
* İl. Gmail ► Untitled docu.. A system consists of a turbine and heat exchanger are connected in series. The working fluid is entering the turbine at P1 0.6 Mpa, T= 200 °C and leaving it with P,= 0.2Mpa. Then the turbine exit becomes the heat exchanger inlet to increase the fluid temperature to become 800 °C. Considering that the adiabatic power y =1.4 and the specific heat = 1.005 KJ/Kg.K. Determine the turbine production work WT and heat exchanger energy needed to be added quE. T = 200 °C P,= 0.6 Mpa- T T2 ? P,=0.2 Mpa h high НЕ T= 800 °C P3 =? 9 in
TNB steam power plant in Genting Highlandsoperates on reheat Rankine cycleand has power net output of 50MW. Steam enters the turbine at aMPa and b °Cand it is cooled in the condenser at a pressure of ckPa by running cooling water from the Bertam River through the tubesof condenser. Steam enters both stages of the turbine at b°C. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed 10 percent, show the cycle on a T-s diagram and determine;i.The pressure at which reheating takes place, ii.The thermal efficiency of the cycleandiii.Please justify how does the thermal efficiency of the cycle if the temperature to low turbine is increase to 600°C? a=12 b=500 c=12
1. A refrigeration system operates on an ideal vapor compression using R-12 with an evaporator temperature of -30°C and condenser exit temperature of 49 30 °C and requires 74.6 kW motor to drive the compressor. What is the capacity of the refrigerator in tons of refrigeration? Enthalpy at condenser entrance = 382 kJ/kg, exit = 248.15 kJ/kg, at evaporator entrance 248.15 KJ/kg, exit = 338.14 kJ/kg.
Q1.2 Consider a two-stage compression refrigeration system operating between the pressure limits of 0.8and0.14 MPa(see Fig. Q 2). The working fluid isrefrigerant -134a. The refrigerant leaves thecondenser as a saturated liquid and is throttled to aflash chamberoperating at0.4 MPa. Part ofthe refrigerant evaporates during this flashing process, and this vapour is mixed with the refrigerantleaving the low-pressure compressor. The mixture is then compressed to the condenser pressure bythe high-pressure compressor. The liquid in the flash chamber is throttled to the evaporator pressure,and it cools the refrigerated space as it vaporizes in the evaporator. Assuming the refrigerant leavesthe evaporator as saturated vapor and both compressors are isentropic, determine(a) the coefficient of performance (COP).Re-draw the schematic diagram and sketch the cycle accurately on a T-s diagram with the propertyvalues labelled at all state points.
It is proposed to design and develop a Rankine cycle Steam Power Plant in which steam at 80 barand 500 oCis supplied to the turbine which exhausts at a pressure of 0.11 bar into a condenser. Condensate from the condenser is returned to Steam Generator (Boiler) by a Feedwater Pump. The processes in the turbine and pump can be assumed to be reversible adiabatic. In addition, pressure and temperature drops can be neglected throughout the cycle. Sketch the T-s diagram for this cycle and calculate the following performance parameters:i) Cycle Thermal Efficiency ii) Work Ratioiii) Specific Steam Consumptioniv) Condenser Heat Loadv) Mass flow rate of steam to generate a net power output of 40 Megawatts (MW).vi) Mass flow rate of cooling water required for the condenser if the cooling water inlettemperature is 26 oC and its outlet temperature is limited to 40 oC. The specific heat capacityof the cooling water is 4.18 kJ/kg K.viii) The total amount of sensible heat in kW supplied to the…
The boiler of a power steam cycle operates at 6000 kPa and the condenser at 50 kPa. At the entrance to the turbine, the temperature is 500°C. The isentropic efficiency of the turbine is 90 percent, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 6.3°C. The boiler is sized for a mass flow rate of 18 kg/s. You are asked to: d. Represent the cycle on P-v and T-s diagrams. Compute the rate at which heat is added in the boiler. Compute the power required to operate the pumps. Determine the net power produced by the cycle. Compute the thermal efficiency.