Answer both questions with small explanations. QuestionIf you want to produce threads in SolidWorks using a sketch, what additional element do you require along with yoursketch?OA new reference planeOA round holeOA triangular holeA square holeA helixO A horizontal relationshipOA vertical relationshipO An extruded cut00QuestionEarly electricity-producing wind turbines usedpredecessorsO WoodO CeramicO PolymerMetalO CompositeO Single crystalO Nano-dotsO Quantum dotsO None of these optionsO All of these optionsblades as did many of their water-pumping

In this problem, it is asking about to produce the threads in solid works by using a sketch then…

If you want to produce threads in SolidWorks using a sketch, what additional element do you require along with your sketch? A new reference plane O A round hole A triangular hole OA square hole A helix A horizontal relationship A vertical relationship O An extruded cut Question Early electricity-producing wind turbines used predecessors Wood Ceramic Polymer Metal O Composite Single crystal Nano-dots Quantum dots None of these options O All of these options blades as did many of their water-pumping

If you want to produce threads in SolidWorks using a sketch, what additional element do you require along with your sketch? A new reference plane O A round hole A triangular hole OA square hole A helix A horizontal relationship A vertical relationship O An extruded cut Question Early electricity-producing wind turbines used predecessors Wood Ceramic Polymer Metal O Composite Single crystal Nano-dots Quantum dots None of these options O All of these options blades as did many of their water-pumping

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.
Please help. Do not just guess. Prove your answer. I will give a good feedback.
There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. Problem: A refrigeration cycle uses refrigerant R-134a to cool down water from 40°C to 20°C. The refrigerant R-134a enters the cycle as saturated liquid at -15°C and exits as saturated vapor at the same temperature. The mass flow rate of R-134a is 0.12 kg/s. The overall heat transfer coefficient is 1400 W/m².K. The surface area of the heat exchanger is 1.4 m². What is the rate at which heat is being exchanged between R-134a and water? Assume that the heat exchanger is perfectly insulated from outside (i.e., there is no convection or radiation with the outside/surrounding). Solution: We know, from the definition of overall heat…
Use Given-Required-Solution in answering problems. Answers should be rounded off to four decimal places and enclosed in a box. · A man is standing at sea level where gravitational acceleration (g) is 32.2 fps?. It is noted that per 998 ft of ascent there is a decrease of 0.0031 fps in the gravitational acceleration. (a) If the man decides to hike a mountain and reaches a point where g 30.5 fps-, how high is the point from sea level? (b) If he traverses the mountain and reaches a point where his weight was decreased by 5 percent, what is the g at this point?
Mechanical Advantage Review Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your engineering design journal. Remember to show all work. 1. A lever has an effort arm that is 8 meters long and the resistance (load) arm that is 5 meters long, how much effort is needed to lift a 200 Newton weight?
Please answer very soon will give rating surely
Answer it correctly please. I will rate with 2-3 votes.
Te-Learning Portal Courses Reports e-Services Which of the following statement is correct Select one: of O Fiction is very bad at rough surfaces ion O Friction is zero for smooth surfaces O Friction is good at smooth surfaces O Friction is high for rough surfaces
kindly create a conclusion regarding Tesla Cars and its factory
In the last few steps, where did 0.4 come from?
answer quickly