A steel tape with a cross-sectional area of 0.039 cm2and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape is 2°C. The measured slope distance is recorded 381.615 m. What is the corrected horizontal distance

Q: Minimum principal stress

A: To find minor / minimum principal stress

Q: LIven: Ex : -533 ×10-6 Ex: -533 x/o-6 Ey 67 x 10-b = -626 x 10-6 E : 30 x/0 psi Y: ,30 Find: Stress…

A:

Q: 5) Determine the FF. L Be вку 3. Stress BD 2. 7 RE

A: Given figure shows a truss. It is required to calculate stresses in member BD,BE, CE and also to…

Q: 140 mm 140 mm A centric load P is applied to the granite block shown. Knowing that the resulting…

A:

Q: the MOHR circle, find the normal stress and shear stress on the shaded plane on the screen

A:

Q: CLO 1: Determine the maximum tensile stress in MPa if P = 115 kN. 20 mm 25 mm 20 mm 3somm O 16.064 O…

A:

Q: 3. A horizontal circular plate weighing 100N is suspended as shown from three wires that are…

A:

Q: Construct mohr circle .Determine radius of mohr circle . Determine maximum principal stress

A: Given data : Normal stress in X direction (σX)=-30 MPaNormal stress in Y direction (σY)=-50 MPaShear…

Q: Determine normal stress across plane passing through 50 degree to the plane 100 N/mm2

A: To Find :- Normal stress at a plane passing through 50° with 100 N/mm^2

Q: A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was…

A: Intensity of Tensile force acting of circular hollow tube, tensile stress, outer diameter have been…

Q: Load (N) Deflection (mm) 0 0   4.903034 0.000346   11.416539 0.000802   18.337648 0.001251…

A: The data you provided is from a load-deflection test on a mortar specimen. It shows how much the…

Q: The fixture shown in Figure 5 is fixed at point A and free at point C. The frame is made from a…

A: Given data  b = 50 mm  h = 75 mm  E = 200 GPA  Ignore axial and shear deformation  Find vertical…

Q: I jp. sin. 05 in. B. 3 kip A9 kip 8 kip Lc-2 kip

A:

Q: The standard length of a tape is 100m having a weight of 2kg with the standard temperature of 20°C…

A:

Q: inclined at 30° to the known directions of the In a stressed member , *0 retio u= 0.3. Determine the…

A: Let normal principal strain in x & ydirection are E1 & E2Ex1 = Ex+Ey2 + Ex-Ey2 cos2θ2 +…

Q: A line is recorded as 472.90m long. It is measured with a 0.65kg tape which is 30.005m long at 20C…

A:

Q: A milling operation was used to remove a portion of a solid bar of square cross section. Forces of…

A:

Q: 2. The masses of the blocks are ma = 30 kg and mg = 70 kg. Between all of the contacting surfaces,…

A:

Q: The thin rectangular plate shown is uniformly deformed such that & = +874 pɛ, ɛ, = -536 uE, and yy…

A:

Q: C Situation 7 - A rectangular bar 50 mm x 75 mm in cross-section is subjected to a tensile force P =…

A:

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Step 1: here we have calculated all the component forces Step 2: here we have calculated the…

Q: Sketch the normal stress distribution acting over the cross section at section a-a. 6 kip 12 kip 3…

A:

Q: P: 23 kN -Calculate the position of the neutral axis. -Calculate the largest and smallest stresses…

A:

Q: A 364-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: Given data in question  Load Coefficient of friction  To find out Determine force P

Q: kN is distributed equally among the three rivets. Determine the tensile stress (MPa) in the plate at…

A: P=70kN Width B=130mm Thickness t=25mm Diameter d=20mm

Q: Convert the stress intensity factor of 3.14PSI √feet to units of Pa √m.

A: Given data- stress intensity factor = 3.14 PSI √feet To Find- It is needed to convert PSI √feet to…

Q: A flat steel bar, 29 mm wide by 5 mm thick and 1.5 m long, is bent by couples applied at the ends so…

A:

Q: A base line was measured with a steel tape of designated length 30 m at 20°C at a pull of 100 N. The…

A:

Q: 4. In the following figure below, assume that a 20-mm-diameter rivet joins the plates that are each…

A:

Q: MPa IR E mm/mm 0=S0,00E + 165 J-160000E 0=J0,0012 (E-0.00 +265

A:

Q: (c) Develop and sketch the Mohr's circle of stresses corresponding to point F. Show all necessary…

A:

Q: The concrete raft foundation Shown inthe ifigure is subject to uniform Soading of 350 KN/m.…

A: Consider the following diagram: Take the rectangle 1, BCGD Breadth, b1 = BC = 4m Length, l1 = BG =…

Q: Another way of testing flexure strength is by quarter point loading as shown. The sample section is…

A:

Q: Question: A contractor want to select a steel bars (diameter 16 mm) produced from two factories (A…

A: "Since you have posted a question with multiple sub-parts, we will solve the first two sub-parts for…

Q: The grain of a wooden member forms an angle of 15° with the vertical. Determine the in-plane…

A: Step 1: Step 2: Step 3: Step 4: