A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross-sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the change in length of segment BC when F₁ = 4.1 kN. F₂-2.3 kN and F3 = 9.6 kN. Input your answer as a value only in mm to two decimal places without +/- sign. -1 m 1.5 m 1.25 m A F₁ B F₂ C D F3

A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross-sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the change in length of segment BC when F₁ = 4.1 kN. F₂-2.3 kN and F3 = 9.6 kN. Input your answer as a value only in mm to two decimal places without +/- sign. -1 m 1.5 m 1.25 m A F₁ B F₂ C D F3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.63*106 m“, determine the following: -100 mm 20 mm -Joint a 80 mm C 20 mm - 68.3 mm 20 mm 60 mm The value of Q is equal to in m3: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:
QUESTION 4 The assembly consists of three titanium (E is 120 GPa) rods and a rigid bar AC. The cross sectional area of each rod is given in the figure. If force of 30 kN is applied to the ring F, determine the horizontal displacement of point F. 1.2 m AcD = 600 mm² %3D 0.6 m 03m E 30 kN 0.3 m AEF = 1200 mm? A AB= = 900 mm2 1.8 m
A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross-sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the change in length of segment BC when F₁ = 4.1 KN, F₂=2.3 kN and F3 = 9.6 kN. Input your answer as a value only in mm to two decimal places without +/-sign. 1 m 1.5 m -1.25 m- A F₁ B F₂ DF3
A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross-sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the displacement of the rod at D when F₁ = 2.8 kN, F₂ = 4.3 kN and F3 = 7.3 kN. Input your answer as a value only in mm to two decimal places without +/-sign. 1m 1.5 m 1.25 m C F2 D F3 A F₁ B
•213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P=50KN, determine is vertical movement. ALUMINUM L=4m A=500mm? STEEL L=3m A=300mm2 E=200GPA E=70GPa 2m 3m
3. A force P is applied to the rigid lever arm ABC as shown. The arm rotates counterclockwise about pin A through an angle of 0.06°. Calculate the normal strain developed in wire BD. Answer: EnD = 0.0014 mm/ mm 300 mm B 400 mm
A brass rod having a diameter of 4 in and a length of 40 ft is suspended vertically from one end. It supports a tensile load of 20 kips at the lower end. If the unit mass of brass is 525lb/ft cube and E=140,000ksi. a. Find the elongation of the rod due to self-weight. b. Find the elongation of the rod due to applied load. c. Find the elongation of the rod if it has a coefficient of thermal expansion of 10 μin/(in°F), and if there’s an increase in temperature by 50 °F. d. What is the total elongation due to loads and temperature?
The rectangular cross-section beam in figure 3b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places. (show all work)
The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the corners B and D are subjected to the displacements that cause the rubber to distort as shown by the dashed lines. 3 mm- D 400 mm A 300 mm- T B 2 mm X
A uniform elastic rod of length 4L and constant cross-section, is fixed at its left end as shown in the figure. An axial force P is acting at the mid-point, C. Assume that plane section remain plane during deformation. The ratio (rounded off to one decimal place) of axial displacements at point A to that at point B is Wall 34 L BC P 21 - 21 x
2.4 The truss shown is the same as in Example 2.1 except that the area of bar ab is a variable. E = 200,000 MPa. (a) For what value of Aah is v. = 0? Is this a function of the magnitude of the applied load? (b) Is it possible to obtain zero u, by varying A? (c) Suppose the applied load were vertical rather than horizontal, would it then be possible to obtain zero u, by varying Aab? If so, for what value of Aab? What would be the corresponding v.? 500 kN Fah = +400.6 kN Aab 4 m 6 m 3 m Problem 2.4 Fac = -277.8 kN Aae = 8000 mm?