Design an l-section purlin, for an industrial building situated in the outskirts of Allahabad, to support a galvanised corrugated iron sheet roof the following data: Spacing of the truss c/c = 6.0 m Span of truss = 12.0 m Slope of roof = 30° Spacing of purlins c/c = 1.5 m Intensity of wind pressure = 2 kN/m² Weight of galvanised sheets = 130 N/m² Yield stress of steel = 250 MPa (USE ONLY IS CODE)

Design an l-section purlin, for an industrial building situated in the outskirts of Allahabad, to support a galvanised corrugated iron sheet roof the following data: Spacing of the truss c/c = 6.0 m Span of truss = 12.0 m Slope of roof = 30° Spacing of purlins c/c = 1.5 m Intensity of wind pressure = 2 kN/m² Weight of galvanised sheets = 130 N/m² Yield stress of steel = 250 MPa (USE ONLY IS CODE)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam carrying floor joist shown in Figure is made of rectangular wood having a dimension of 50mm x 100mm. Compute the maximumdeflection if E = 8.47 x 10^3MPa (for guijo, stress grade 80).
PLEASE INCLUDE COMPLETE SOLUTION
18. A steel loop ABCD of length 1.2 m and of 10-mm diameter is placed as shown around a 24 mm diameter aluminum rod AC. Cables BE and DF, each of 12 mm diameter, are used to apply the load P. Knowing that the ultimate strength of the steel used for the loop and the cables is 400 MPa and that the ultimate strength of the aluminum used for the rod is 220 MPa, determine the largest load P that can be applied if an overall factor of safety of 3 is desired. a. 37.7 KN b. 39.7 KN E С. 74.6 KN d. 45.2 KN B 180 mm 480 mm A 180 mm D
Provide complete and neat solution
Need it urgent
Dont round off in solution, only round off in final answer in 2 decimal places. Answer asap
Determine the maximum flexural stress in the beam loaded as shown below
ANSWER ONLY AC BC CDwrong answer gets downvote so double check the answer cause it will be input in the system
Mr. Pine lives on the 13th floor of the Xcel building in Denver. He has decided to extend his existing d1 ft deck (d1 = 3 ft) and add a swimming pool. To get approval for his pool, Mr. Pine must provide information to the building manager. He has hired you to provide: (1) the resultant of the distributed load f(x) lb (2) where the resultant acts relative to point A (3) the reactions at point A due to the addition (distributed load) Given: d2 = 33 ft and f(?) = 215x2 + 3749 lb with x measured from point A
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V: 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Truss Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm W = 79 N/m 12 12 1.2 I Allowable bending stress Fbx= Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D+ L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
Two 10-in 15.3-lb channels are welded together as shown in the figure. Compute the value of Tx
A 6m steel wire hanging on one end has a weight of W, it supports a load of 243 kN, determine the required diameter if the elongation would not exceed 1.69 mm, Assume E = 2 GPa.