A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column and column head are 500 x 500 mm and 750 mm x 750 mm as shown in Fig. 14.34a. The superimposed dead and live loads are 2 kN/m² and 4 kN/m2. The height of the floor is 5 m. Design the slab. (Use IS CODE) CAL C/L 750X750 COLUMN HEAD TCAL 3000 3000 C/L 3000 --- 1 3000 3000 COLUMN MIDDLE 3000 COLUMN STRIP STRIP STRIP 6000 (a) PLAN OF INTERIOR PANEL Fig. 14.34a T COLUMN STRIP MIDDLE STRIP COLUMN STRIP 6000

A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column and column head are 500 x 500 mm and 750 mm x 750 mm as shown in Fig. 14.34a. The superimposed dead and live loads are 2 kN/m² and 4 kN/m2. The height of the floor is 5 m. Design the slab. (Use IS CODE) CAL C/L 750X750 COLUMN HEAD TCAL 3000 3000 C/L 3000 --- 1 3000 3000 COLUMN MIDDLE 3000 COLUMN STRIP STRIP STRIP 6000 (a) PLAN OF INTERIOR PANEL Fig. 14.34a T COLUMN STRIP MIDDLE STRIP COLUMN STRIP 6000

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Design a simply supported rectangular reinforced concrete beam. Note: Neglected the self-weight of the beam. Wu (D.L) PLL Wa (L.L) h b W D.L P LL W LL Fc bar No. of Fy MPа MPa (mm) (mm) (m) kN/m kN kN/m dia. layers 325 500 17 50 20 20 two 28 420
Pls. AnswerGiven: f'c = 35 MPa fy= 415 MPaSolve for Slab S-1 (only)
Plate No.1: Structural Loads Calculation 1. The hollow core panel is made from plain stone concrete. Determine the dead weight of the panel. The holes each have a diameter of 100mm. 175 mm 300 mm 300 mm 300 mm/ 300 mm/ 2. The pre-cast T-beam has the cross-section shown. Determine its weight per foot of length if it is 3.6 m 300 mm/ made from reinforced stone concrete and eight 3/4-in. cold-formed steel reinforcing rods. 300 mm/ 8 in. 8 in. 20 in. -15 in. 15 in. 6 in. 6 in. 6 in.
Problem Set 3: The overhanging beam carries a uniformly distributed load totaling 8W and two concentrated loads of magnitude W each. Determine the safe value of W if the working stresses are 3 000 psi in tension and 10 000 psi in compression. W 8W W Lam AV BV V VC 1 in 12 in 4ft 16ft 4ft D 8 in 1 in
7. 20 ft I KLF Mmax A max =
Discuss aboout Self-straining loads
A simply supported beam has a height of 600 mm and a width of 300mm. Determine the maximum safe live load that the beam can carry. The dead load is the beam weight plus a superimposed load of 15 kN/m The stirrup size is 12 mm, the top bars are 2-20 mm and the bottom bars are 5-28 mm. The clear distance between layers of bottom bars is the bar size, 28 mm. Use fc'=30 MPa, Grade 60 (fy=414 MPa) reinforcements and concrete cover of 50 mm.
USE NSCP 2010 A simply supported one way reinforced concrete floor slab has a spanof 3 m. It carries a service live load of 8.4 kPa and a service dead loadof 1.2 kPa. fc’ = 20.7 MPa, fy = 414.6 MPa. Use steel covering of 25 mmmeasure from center of bars. Calculate the spacing of the 12 mm øshrinkage and temperature bars for minimum thickness of slab.
b) The floor system shown is subjected to a total uniform distributed load of 20 kN/m². Sketch the loading that acts along the members and CDE. 2 m E 3 m F G H 4 m 3 m
What is the ultimate uniaxial load capacity of the given column section, according to the design strengths of the materials? Concrete is C30, longitu- dinal steel bars and ties are B420C. Longitudinal bars are o14, ties are o10. b= 300 mm, h= 400mm. The column will be produced on site with adequate quality control. %3D h 1357 kN b) 750 kN 2490 kN d) 1150 kN 1470 kN Leave blank
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)
TRIBUTARY METHOD OF LOAD DISTRIBUTION (3) 2. Consider the floor plan shown in Figure. The floor is 100mm thick F-6 @ 6.67' = 40 %3D C4 I- reinforced concrete. Determine the B2 GI B3 following: (a) load that acts on floor beam B1, (b) load that acts on beam B5, (c) the load acting on corner column C1, and (d) the load acting on interior B4 2 @ 10' = 20' B) C2 I- B5 –I- I G4 G2 G3 B1 5 @ 8'= 40' column C2 ©-I- C3 Ci 40' 20 *Neglect the weight of joists