A steel plate used for polymer forming is to be bent into a circular shape having an inside radius of 8 m. What maximum thickness can be used for the plate if the normal stress is not to exceed 254 MPa? Assume that the modulus of elasticity for the steel is 207 GPa.

A steel plate used for polymer forming is to be bent into a circular shape having an inside radius of 8 m. What maximum thickness can be used for the plate if the normal stress is not to exceed 254 MPa? Assume that the modulus of elasticity for the steel is 207 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE ANSWER ALL OF THE GIVEN QUESTIONS. Choose from the given choices/options below the question. I will rate you with “UPVOTE/LIKE” if you answer all of the questions. I will rate you with “DOWNVOTE/DISLIKE”, if you don’t answer all of the questions. THANK YOU FOR YOUR HELP.
How can we find the location of the neutral axis?
Round off the following number to three significant figures:2553N
Page) #5: A certain rocket engine has a temperature when in use of approximately 182°C. If left to cool in a 20°C room for 24 hours, it is known that the engine temperature will be 26°C. If the engine obeys "Newton's Law of Cooling", how long in hours would the engine have to cool after use before it reaches 74°C? #5: answer correct to 2 decimals Save Your work has been saved! (Back to Admin Page)
I need the answer as soon as possible
Topic: Dynamics (Work, Energy, Power) Determine: (a) The force (parallel the inclined) required to move the block. (b) The rate of work done in 10 seconds (c) The initial velocity (Vi) of the block if its velocity at 10 meters is 30 m/s. *Please answer with complete and in order solution. *Three decimal places all final answers. *Include figures and Free Body Diagram with proper labels. *Enclose with a box all final answers. THANK YOU
Need help solving this problem. Please provide clear and concise steps in neat handwriting.
(b) The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank and the pressures at points (1) and (2).
Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response:
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o rad/s. At o = 0 rad/s, the U-tube contains 20-cm-high alcohol in both arms Q3 (a) Determine the new o when the elevation difference between the fluid surfaces in the two arms is 30 cm.