An aluminum alloy cylinder with a diameter of 3 inches and a height of 6 inches is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 x 10 6 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?

An aluminum alloy cylinder with a diameter of 3 inches and a height of 6 inches is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 x 10 6 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
An aluminum alloy cylinder with a diameter of 76 mm and a height of 150 mm. is subjected to a compressive load of 220 kN. Assume that the mate-rial is within the elastic region and a modulus of elasticity of 75 GPa. a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?
7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses in the two materials with an applied load of 45,000 lbs. 45,000 lbs 3.5"Ø 3.0"Ø Steel Aluminum
A composite column is formed by placing a steel bar, 20 mm in diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm, respectively. The column is then subjected to an axial load of 50 kN. If E for steel is 200 OOO N/mm’ and E for the alloy is 70 000 N/mm’, calculate the stress in the cylinder and in the bar, the shortening of the column and the strain energy stored in the column.
Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch radius hole centered on its width, as shown in the sketch. With an axial load, P = 8650 lbs applied, the maximum axial stress at the edges of the hole was experimentally determined to be 7670 psi What is the stress concentration factor, K, of the hole? 1.33 0.75 1.66 1.50 P 2.50 in. -Radius 1/4 in. P= 8650 lbs
A hot-rolled steel bar has a diameter of 12 mm was subjected to a tension test as shown in the figure below. Determine the following. a. If the recorded yield stress was 380 MPa, what is the value of the yielding force (P) in kN? b. If the value of the (P) ultimate was 66 kN, what is the ultimate stress in MPa? c. If the modulus of elasticity (E) of the steel equal to 2 x 105 MPa and stress at the proportional limit equal to 276 MPa, what is the corresponding elastic strain? And what is the unit of this strain? d. If the recorded fracture stress was 490 MPa and the fracture force was 40 kN, what is the diameter of the bar at fracture? e. What can be obtained from the 0.2% offset method? D, = 12 mm
Question: Determine the diameter of the elastic core of the rod ? Options: A. 13.72 mm B.10.34 mm C.11.57 mm D.12.95 mm A solid steel rod is 1.5 meters long and has a diameter of 20 mm. The steel rod is assume to be an elastoplastic material with G = 77 GPa and a yield shear stress of 145 MPa.
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load. Calculate the resulting diameter of the rod. If the rod is sub- jected to a compressive load of 2000 lb, what will be the diameter of the rod? Assume that the modulus of elasticity is 10,000 ksi, Poisson’s ratio is 0.33, and the yield strength is 21 ksi.
An aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 * 106 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?
Problem # 4 A 4 in x 3 in steel block follows an elasto-perfectly plastic stress strain relation with a yielding stress 0,-60 ksi and a modulus of elasticity E=30 x 10° psi. The block is reinforced on the top and bottom by 1 in x 3 in plates that are perfectly elastic having a rupture stress O,-60 ksi and a modulus of elasticity E=10 x10° psi. The stress-strain relation for the two materials are given below. • Determine the largest moment M that can be applied to the cross section before it fails. • Determine the magnitude of the distributed load w (kip/ft) that can be applied to a 12-ft beam made of that cross section. 1 in 4 in. M 1 in 6 ft 6 ft 60 ksi 60 ksi 3 in. Gy E-30x10'ksi E-10x10 ksi 6x 10 stress-strain diagram for 4 in x 3 in stress-strain diagram for 3 in x 1 in plates