A square steel plate is perfectly insulated above and below, so the only heat flow is through the plate itself. Each side is kept at a constant temperature, but this can be different on each side. To approximate the temperature at an interior point of the plate, we use the rule that averages the temperatures of its four neighboring points, let T1...T6 be the temperature of the 6 interior nodes of the plate, which are visible in the figure below, Calculates the values of the temperature inside the steel plate.

A square steel plate is perfectly insulated above and below, so the only heat flow is through the plate itself. Each side is kept at a constant temperature, but this can be different on each side. To approximate the temperature at an interior point of the plate, we use the rule that averages the temperatures of its four neighboring points, let T1...T6 be the temperature of the 6 interior nodes of the plate, which are visible in the figure below, Calculates the values of the temperature inside the steel plate.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.10P: 5.10 Experiments have been performed on the temperature distribution in a homogeneous long cylinder...

See similar textbooks

Similar questions

Q2/ A (2 cm) thick steel plate of thermal conductivity (50 W/m.°C) has a uniform heat generation of (40 x 106 W/m³). The temperature at the left surface of the plate is (160 °C) and at the right surface is (100 °C) start from principle to find the place and the value of the maximum temperature. (25 marks)
Which formula is used to calculate the heat conduction in the AXIAL direction in a vertically located pipe segment whose inner and outer surfaces are perfectly insulated. Here r, is inner radius, r, outer radius, Tri pipe inner surface temperature, Tro pipe outer surface temperature, L is the length of the pipe, T the temperature on the lower surface, Ty the temperature on upper surface. Tu r; Tro r
A plane wall is insulated on its left side (? = 0). The wall generates energy uniformly at arate of ?̇ [W m 3⁄ ] and has thermal conductivity ?. On its right side (? = ?), the wall is exposedto a fluid at temperature ?" with convection coefficient ℎ.a) Draw a schematic of this plane wall. Make the schematic large enough that you cansketch the temperature profile within the wall after solving for it in later steps.b) Write out the full form of the Heat Diffusion Equation (HDE) in the appropriatecoordinate system for this physical scenario. Simplify the HDE and write out theappropriate boundary conditions in their general form (e.g., ?| #$% = ?& ).c) Derive an expression for the steady-state temperature distribution ?(?) within thewall. You may start from the general solution provided in Appendix C of the Bergmantextbook; or you may derive the solution directly from the differential equation andthe boundary conditions. Annotate your schematic by sketching the temperatureprofile…
Completely solve and box the final answer. Write legibly 3. Determine the heat loss in KW of a vertical furnace made up of inner wall of firebrick 28 cm thick followed by insulating brick 18 cm thick and an outer wall of steel 1.5 cm thick. Surface temperature of the wall adjacent to the combustion chamber is 895ºC while that of the outer surface of steel is 42ºC. Use a thermal conductivity of wall in W/m-ºK for firebrick, insulating brick and steel to be 14, 0.92, and 52 respectively. The cross section is 2.5 m x 7.5 m.
A wall of a house is made from two layers of bricks enclosing a layer of insulation. A radiator is positioned to cover the whole internal surface, and used intermittently when the internal temperature is low. The external surface is exposed to the outside air. Which of the following assumptions could be used to identify the relevant reduced form of the conduction equation to find the temperature in the wall. a. Conduction is mainly in two directions. b. Conduction is mainly in one direction. c. The wall properties are homogeneous. d. Steady conditions exist. e. Unsteady conditions exist. f. There is an internal volumetric heat generation in the wall.
Q1 Passage of an electric current through a long conducting rod of radius r; and thermal conductivity k, results in uniform volumetric heating at a rate of ġ. The conduct- ing rod is wrapped in an electrically nonconducting cladding material of outer radius r, and thermal conduc- tivity k, and convection cooling is provided by an adjoining fluid. Conducting rod, ġ, k, 11 To Čladding, ke For steady-state conditions, write appropriate forms of the heat equations for the rod and cladding. Express ap- propriate boundary conditions for the solution of these equations.
Question: USE CRANCK NICKLISON METHOD TO Find the steady state temperature distribution at all points of a heated steel plate .The plate has 30 cm width and 30 cm in length . The edges of the sheet are kept at constant temperature: 100 , 80 , 60 ,40 degrees. Assume the sheet is divided into 3x3 grids.
under steady-state conditions. If you are given T1 = 200 °C and T2 = 164 °C, determine: a) the conduction heat flux, q,.cond, in m2 W from x = 0 to x = L b) if the dimensions of the triangle ares 15 mm and h 13 mm, calculate the heat transfer due to convection, q,y, in W at x = L Finsulation T2 T T = 20°C h = 500 W/m2.K Triangular Prism x L x 0 L= 50 mm k = 100 W/m-K
Choose the correct answer and give step by step solution for this
2. The slab shown is embedded in insulating materials on five sides, while the front face experiences convection off its face. Heat is generated inside the material by an exothermic reaction equal to 1.0 kW/m'. The thermal conductivity of the slab is 0.2 W/mk. a. Simplify the heat conduction equation and integrate the resulting ID steady form of to find the temperature distribution of the slab, T(x). b. Present the temperature of the front and back faces of the slab. n-20- 10 cm IT- 25°C) 100 cm 100 cm
Completely solve and box the final answer. Write legibly 1. How much heat will be transferred in KW if a hot gas at 175ºC crosses a wall 100-mm thick and cross-sectional dimensions of 25 cm x 52 cm. It leaves the wall at 52ºC. The thermal conductivity of the wall is 12.4 W/m-ºK?
You are tasked to design a cooling system for an ice rink. A standard ice rink has surface area ofArink = 1580 m2 . In this design, a technologically advanced solid state thermoelectric generatingcooling plate is placed in between concrete slabs. The following diagram contains the dimensionalparameters of the design (a) In the space below, with your best effort to correspond to the above diagram, draw a thermalcircuit that establishes the relationship between the cooling plate’s heat rate, Q, and the system’stemperatures and thermal resistances. Label the appropriate dimensions, thermal conductivities,convection coefficient, and temperatures. Ignore effects from contact resistance. (b) Given that the temperature at the top surface of the ice must be T ice = -5°C, obtain the requiredheat rate Q that must be drawn by the cooling plate in units Kilowatts. Be careful of +/- sign.Answer: ____________________________ [kW] c) Using the thermal circuit you established in Part (a), obtain the…