Passage of an electric current through a long condu rod of radius r; and thermal conductivity k, resu uniform volumetric heating at a rate of ġ. The cor ing rod is wrapped in an electrically noncondu
Q: Question Perfectly insulated thin rod of finite length, vod is heated with external heat Source V,…
A:
Q: A pipe carrying hot water experiences an external cross flow of cold air. Given steady-state conditi…
A: Given that, hot water is flowing inside a pipe and cold air is flow at the outer surface of the pipe…
Q: Derive the general 3D-general heat conduction equation for a spherical coordinate.
A:
Q: How important the forced and free convection know as a mechanical engineer?
A:
Q: er a thorough derivation by Doraemon to establish an equation for cylindrical fuel rod of a nuclear…
A:
Q: A cylinder (20 mm in diameter and 100 mm long) is heated internally by an electrical heater and is…
A: Given; Cylinder diameter, D=20 mm=0.02 m Cylinder length, L=100 mm=0.1 m Air velocity, V=20 m/s Air…
Q: Determine if the following heat transfer scenario can be simplified to steady heat transfer by…
A: All three conditions are categorized in S or 1D type. 1. 1D 2. S + 1D 3. 1D + S
Q: A stove in the form of a cube (L = 1m) it is located inside. External walls of the stove, according…
A: Given Data :- k = 0.0269 w/mk Pr= 0.72 v= 1.75*10^6
Q: The composite wall of an oven consists of three materials, two of which are of known thermal…
A:
Q: A 5-cm-thick beef steak is being frozen in a -30°C room. The product has 73% moisture content,…
A: Given, The thickness of beef, a=5 cm=5×10-2 m The initial freezing temperature, Tf=-1.75…
Q: In a quenching process, a copper plate of 3 mm thick is heated up to 350°C and then suddenly, it is…
A: Explanation: first Bi number is calculated to check the validity of lumped analysis which must be…
Q: 3.37 Measurements show that steady-state conduction through a plane wall without heat generation…
A:
Q: The steady state temperature3/3 distribution in a one dimensional wall of thermal conductivity…
A: Write the expression of temperature distribution of one dimensional wall. T=a+bx2 Write the…
Q: A round solid cylinder made of a plastic material (a = 6 × 10-7 m³/s) is initially at a uniform…
A: (a) We consider a control volume (CV) and study the heat transfer from and to this CV in a short…
Q: In fabrication process, steel components are formed hot and then quenched in water. Consider 2 m…
A: The Biot number can be calculated as, Since the value of the Biot number is more than 0.1, the…
Q: We have a system made up of a glass container (glass) whose bottom and top have been insulated. A…
A: It is asked to find the heat transfer coefficient in the case mentioned above
Q: Example: A large plate of aluminum 5.0 cm thick and initially at 200◦C is suddenly exposed to the…
A:
Q: A cylindrical resistor element on a circuit board dissipates 0.22 W of power in an environment at…
A: Heat flux (Ф) is the rate of heat energy transmission via a particular surface (W), whereas heat…
Q: Let's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential…
A:
Q: An air flow with velocity u∞ = 2m/s and T∞ = 300K is used to cool the surface of a flat metal plate…
A:
Q: The composite wall of an oven consists of three materials, two of which are of known thermal…
A:
Q: 7. The composite wall of an oven consists of three materials, two of which are of thermal…
A:
Q: A 5 cm-thick beef steak is being frozen in a -30°C room. The product has 73% moisture content, a…
A:
Q: Steel balls 10 mm in diameter are annealed by heating to 1,150 K and then slowly cooling to 450 K in…
A: Given Diameter, d = 10 mm Thermal conductivity, k = 40 W/mK Convection…
Q: An uninsulated steam pipe passes through a room in which the air and walls are at 25°C. The outside…
A:
Q: A copper sphere of 18 mm diameter (density = 8960 kg/m3 and CP= 0.38 kJ/kg K) is exposed to air at…
A: Diameter of copper sphere, D=18 mmDensity of copper, ρ=8960 kg/m3Cp=0.38 kJ/kg.KAir Temperature,…
Q: A radioactive sphere of 20-cm diameter generates heat at the rate of 300 W. It is cooled by placing…
A:
Q: A food product to produced in the form of small round (pellet) with frozen in the freezer water…
A:
Q: A long cylindrical nuclear fuel rod has the following steady-state temperature distribution: T(6) =…
A:
Q: Continuous temperature distribution in a semi-permeable material with laser radiation on it,…
A:
Q: An oven in our factory has wall of 35 cm thicknesl with inner temperetur 650°C and outer tempercture…
A: given; thickness (t)=35cm=0.35minner temperature(T1)=6500coutput temperature (T2)=950csurrounding…
Q: Q2. Consider a cylinder of radius R with uniformly distributed heat sources and constant thermal…
A: Refer the answer in next page.
Q: 1-) Assume steady-state, one-dimensional heat conduction through the symmetric shape shown. Assuming…
A:
Q: A pupe 20 cm in diameter contains steam at 150 °C and is protected with a covering 5cm thick for…
A: Let q cal./sec. be the constant quantity of heat flowing out radially through a surface of the pipe…
Q: Consider a wall of thickness 50 mm and thermal conductivity 14 W/m.K, the left side (x-0) is…
A:
Q: Radioactive wastes are pack
A: Consider the diagram shown below for the given sphere. Assumptions: Steady-state heat transfer One…
Q: Q4. A block of pure aluminum, initially at 90°C, is placed in front of a fan. ASsuming lumped…
A: given data al block initially at 90 degree C
Q: The roof of a house absorbs a solar radiant flux of 600 W/m", while the underside to the ceiling is…
A: Q= h A ( T2-T1) q= Q/A = h( T2-T1)
Q: at flow as a result of the contact of the blocks, plot the temp s a function of time, using the…
A: Draw the fitting chart of the 3D squares and cuboid subsequent to going along with them
Q: Q4. A thick steel slab (p=7800 kg/m', C-480 J/kg. k, k-50 W/m. k, a 10-5 m2 by water jets impinging…
A:
Q: Plate glass 5 mm thick at 200°C is to be cooled from both sides using air at 40°C. If surface cracks…
A:
Q: The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick…
A:
Q: A certain liquid flow inside a 4 cm diameter pipe, 6 meter long with an entering temperature of 350…
A: Given data: di=4 cmL=6 mT=350°CTw=575°Cm˙=60 kg/minPr=0.003μ=0.003 N.s/mk=6.2 w/m-k, Cp=0.41 kj/kg-k…
Q: Water at a temperature of T∞= 25°C flows over one of the surfaces of a steel wall (AISI 1010) whose…
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- 1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.5.10 Experiments have been performed on the temperature distribution in a homogeneous long cylinder (0.1 m diameter, thermal conductivity of 0.2 W/m K) with uniform internal heat generation. By dimensional analysis, determine the relation between the steady-state temperature at the center of the cylinder , the diameter, the thermal conductivity, and the rate of heat generation. Take the temperature at the surface as your datum. What is the equation for the center temperature if the difference between center and surface temperature is when the heat generation is ?1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
- 2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .(a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = = W 3 m. k . Ay m-1, n m, n | Δx=" m, n+1 m, n-1 The side insulatedFor each of the following cases, determine an appropriate characteristic length Lc and the corresponding Biot Bi number that is associated with the transient thermal response of the solid object. Say if the global capacitance approximation is va lid. If temperature information is not provided, evaluate properties T = 300K a)oroidal shape with diameter D = 50mm and cross-sectional area AC = 5 mm², with thermal conductivity k = 2.3W / (mK) The surface of the toroid is exposed to a refrigerant corresponding to a convective coefficient eta = 50 W/( m2.k) b)A long stainless steel heated bar (AISI 304), with rectangular cross section, and dimensions w = 3mm , W = 5mm and L = 100mm . the bar issubjected to a refrigerant that provides a heat transfer coefficient of h =15 W/(m2 K) on all exposed surfaces. c)A long extruded aluminum tube (2024 Alloy) with internal dimensions and external w = 20 mm and W = 24 mm , respectively, suddenly submerged in water, with a convective coefficient of h =…
- A solid cylinder of radius R and length L is made from material with thermal conductivity 2. Heat is generated inside the cylinder at a rate S (energy per unit volume per unit time). (a) Neglecting conduction along the axis of the cylinder, find the steady-state temperature distribution in the cylinder, given that the surface temperature is Ts. (b) Consider a crude approximation of a mouse modeled as a cylinder of radius 1 cm and length 5 cm. If the ambient air temperature is 10°C and the internal rate of heat generation in the animal is 10-³ W/cm³, find the skin temperature (Ts) for the mouse. The external heat-transfer coefficient is h = 0.2 W/m².K. (You can neglect conduction along the axis of the mouse, as in part a.)Consider a solid sphere of radius R with a fixed surface temperature, TR. Heat is generated within the solid at a rate per unit volume given by q = ₁ + ₂r; where ₁ and ₂ are constants. (a) Assuming constant thermal conductivity, use the conduction equation to derive an expression for the steady-state temperature profile, T(r), in the sphere. (b) Calculate the temperature at the center of the sphere for the following parameter values: R=3 m 1₁-20 W/m³ TR-20 °C k-0.5 W/(m K) ₂-10 W/m³(a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = W 3 m. k Ay m-1, n 11- m2, 11 m, n+1 m, n-1 The side insulated
- An oven in our factory has wall of 35 cm thicknesi with inner tempereture Ot 650°C and outer tempercture 95°C, Air flows at 23°C (it is also tempereture of surrounding) 0.8 end heat convection coefficient betwren woll end air is h=20 heat conduction coefficient of the woll? )on this woll, woll's outer surfoce heat emmisivity coefficient is colculoteDerive the general 3D-general heat conduction equation for a spherical coordinate.(a) Consider nodal configuration shown below. Derive the finite-difference equations under steady-state conditions for the following situations. (a) The boundary is insulated. (b) The boundary is subjected to a constant heat flux. m, n+1 Ay Im, n The side insulated m-1, n I I Ax- m, n-1