Answered: A slotted machine link 6mm thick is…

A slotted machine link 6mm thick is subjected to a tensile load of 40kN acting along the centreline of the end faces. Find the stress distribution for a section through the slot such as AA.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The one end of a hollow square bar whose side is 10.35 in with 1.35 in thickness is under a tensile…

Q: Cônnecting Ród óf å Diesel Engine cross section. It is subjected to a force of 85KN. Calculate the…

A: area of the I cross section is =2×21×6 + 5×35=427mm2=427×10-6m2

Q: A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum ten sile…

Q: A) What is the axial force along AB? FAR = units B) What must be the minimum diameter of the pin at…

A: Given:P=200 lbFoS=2.5shear stress at failure for the pin material= 16 ksi

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronzel A=…

A: σsteel=120Mpaσbronze=70Mpato find:- Maximum load(P)

Q: If a 10kN load is applied on steel rod of diameter 10mm , the normal stress will be

A: Normal stress is a measure of the internal forces experienced by a material, such as a steel rod,…

Q: Parvinbhai

A: The objective of this question is to determine the required width of an offset link that supports a…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

Q: The one end of a hollow square bar whose side is 10.68 in with 1.68 in thickness is under a tensile…

Q: 2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the…

Q: A 36-KN load P is supported by the three rods below. Determine the following: a. The change in…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

A: Given Data:- Side(s) =0.1m = 3.93inch.......considering the unit as meters Thickness (t) =0.01m =…

Q: Problem 2: Use an eigenvalue approach to solve for the principal stresses and directions for the…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

Q: TEST I: 1 Find Mhe allowable safe load P if the stresses in the bar are the folbuwing. AB= 56 cgi…

A: Given data:-Stress in bar AB, σAB=50ksi=344.738N/mm2Stress in bar BC, σBC=60ksi=413.685N/mm2Stress…

Q: Q-23: A crane hook has a cross section that is approximated by the trapezoidal section shown in Fig.…

A: The maximum stress that can be applied is .The dimension of trapezium are

Q: The two plates are joined together using a rectangular pin. What is the smallest width of the plates…

A: given data: applied load (P)=45KN=45*103N dimension of pin=wx15mm allowable shear stress (τs)=120MPa…

Q: The lap joint carries an P axial load of P - 50 kN. It is connected by 3-18 mm 150 mm 20 mm 20 mm…

A: As given question Load =50 kn T=20mm n=3 Dia=18mm We have to find shear stress, bearing stress and…

Q: The one end of a hollow square bar whose side is (10.13) in with (1.13) in thickness is under a…

Q: ADISIDO diameter is 10 times the tube thickness, find the thickness (mm) of the tube.

A: Given Load, P = 500 kN Stress = 140 MPa Find Thickness, t

Q: The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Given Data: The side of the hollow square bar is s =10.47 in. The thickness of the bar is t = 1.47…

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: The one end of a hollow square bar whose side is 10.69 in with 1.69 in thickness is under a tensile…

Q: Find the tensile load which produce stress of 2.5 N/mm2 and cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ Required : Tensile load

Q: WERS. I WILL REPORT

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: 10 0M, -FXED SUPPORT Find the principal stresses and maximum in-plane shear stress at element A.…

Q: Compare the maximum stress induced into a rectangular plate 100mm long, 50mm width and 10mm…

A: The formulae for stress would be the ration of load to cross section area. The given problem will…

Q: Problem 2: A circular rod tapers in diameter from 50 mm from one end to 20 mmon theother end for a…

Q: 1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1.…

Q: A pin connection, like that shown in Figure 1-16, is subjected to a force of 16.5 kN. Determine the…

Q: Find the smallest and safestd of the link as shown on the figure, if the working stress is equal to…

A: Find the smallest diameter

Q: A prismatic bar PQRST is subjected to axial loads as shown in the figure. The segments having…

Question

A slotted machine link 6mm thick is subjected to a tensile
load of 40kN acting along the centreline of the end faces.
Find the stress distribution for a section through the slot
such as AA.
40kN
→X
-
D
B
ΓΑ
A
10
_10
30
40kN
30
6
с
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

asap pls
A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside diameter if the ultimate tensile stress is 600MPa and a factor of safety is 5.
Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction, 50mm width into y-axis direction and 10mm thickness into z-axis direction is subjected to tensile load of 10kN into y-axis direction for bellow cases: 1- As a solid plate. 2- The same plate with a Circle hole 10mm diameter in xy-plane in the center the plate.
Please explain in details thank you !!
I neeed typing clear
The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ_all=243 ksi for pin material.
The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take oall = 243 ksi for pin material.
I need both parts solution if u dont know both parts please skip if u give me right ans i surely gives u like
Steel bar with dimensions with (10mm and 10mm) subjected to axial load of * 2000N. Determine the stress P 10mm 10mm L=100 mm
ANSWER WITH CLEAN SOLUTIONS AND WITH FREE BODY DIAGRAM
The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σallowable=243 ksi for pin material.