A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions are as follows: outside diameter = 32.0 mm, inside diameter = 28.0 mm, and length = 1.00 m. Compute the tensile force required to produce an elongation of the bar of 1.3 mm. Would the stress produced by the force just found be safe if the load is applied repeatedly?

A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions are as follows: outside diameter = 32.0 mm, inside diameter = 28.0 mm, and length = 1.00 m. Compute the tensile force required to produce an elongation of the bar of 1.3 mm. Would the stress produced by the force just found be safe if the load is applied repeatedly?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.5P: An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with...

See similar textbooks

Similar questions

What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?
The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress=0.4*Yield strength. Assume material is 1020 hot-rolled steel.
You are in charge of designing a new fixture for a “universal testing machine” that will attach a tensile specimen to the machine using a clevis—a U-shaped piece with holes drilled through the two arms—and a cylindrical pin that passes through the clevis and the specimen. If the maximum load exerted by the machine is 30 kN and the pin is to be made of some sort of steel, what is the minimum pin diameter needed to ensure that the shear stress in the pin does not exceed 600 MPa? Assume that the steel has similar elastic properties to pure Fe.
Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.
The pin in the image shown must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear Stress = 0.4*Yield strength. Assume material is 1020 hot-rolled steel.
A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power to an agricultural locomotive. If the dimensions of the square key is 0.5 x 3 in, what is the maximum force in the pulley’s belt that can be transmitted if the shear stress is limited to 8500 psi and bearing stress limited to 4000 psi?
In Figure 1, with its dimensions, loading status and material properties, different full circle cross-section rod has been given. The AB part of the rod is steel, 100 mm in diameter; BC part is copper and its diameter It is 80 mm. (a) Draw the normal force diagram of the bar. (b) Calculate the normal stresses to occur in parts AB and BC. (c) Calculate the total length change of the rod. çelik=steel , bakır=copper L4(cm)=230 , L5(cm)=240 , P1(kN)=124 , P2(kN)=58
In Figure 1, with its dimensions, loading status and material properties, different full circle cross-section rod has been given. The AB part of the rod is steel, 100 mm in diameter; BC part is copper and its diameter It is 80 mm. (a) Draw the normal force diagram of the bar. (b) Calculate the normal stresses to occur in parts AB and BC. (c) Calculate the total length change of the rod. çelik=steel , bakır=copper , şekil 1 = figure 1 L4(cm)=230 , L5(cm)=240 , P1(kN)=124 , P2(kN)=58
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.
Please solve the problem with a neat paper sheet. The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch.
1. The tie-rods in the press in Figure are made of the steel alloy SAE 5160 OQT 900 (E=30×106 psi). Each rod has a diameter of 2.00 in. and an initial length of 68.5 in. An axial tensile load of 40 000 lb is exerted on each rod during operation of the press. Compute the deformation of the rods. Press frame Ram Circular steel tie rod attached to press frame Die A cross sectional area Original length Total deformation
The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb. Rapid cycling for many million cycles is expected. As the tensile load fluctuates between 4,000 lb and 1,200 lb, it creates fluctuating normal stresses. Calculate the following stresses at the section through the hole. Note: SAE 1050 OQT 1300 steel, wrought steel (a) Maximum tensile stress (psi) (b) Minimum tensile stress (psi) (c) Median stress (psi)