A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal 100 A and the source frequency is 60 Hz. The DC output voltage is to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary 本D太D,太D, R 本D。太D。去D Select one: O a. 0.875 O b. 0.955 Oc. 0.551 O d. 0.432

A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal 100 A and the source frequency is 60 Hz. The DC output voltage is to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary 本D太D,太D, R 本D。太D。去D Select one: O a. 0.875 O b. 0.955 Oc. 0.551 O d. 0.432

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
a) Draw the 3-phase half-wave uncontrolled rectifier circuit for resistive load.b) Briefly explain the purpose of use.c) Draw the sinusoidal input voltages and the output voltage on the load.
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
In a centre-tapped full wave rectifier having a load resistance resistance equals 3 2. The turn's ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS ), 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency. 750 52 diode forward bias
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
In a centre-tapped full wave rectifier, the diode having a forward resistance of 3 ohm and the load resistance equals to 750 ohm. The turns ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS) 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency.
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110v/11-0-11 V is used with R1-1 Kn. Assume diode as Germanium. a) Find Input Voltage D, Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. eelee
For the single phase half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 50 Hz. The load resistor is 5ohm. Determine (a) the average load current, (b) the average power absorbed by the load and (c) the power factor of the circuit.