Answered: A 60 kN/m 2.0 m B 120 kN.m 3.0 m 30 kN…

Engineering

Civil Engineering

A 60 kN/m 2.0 m B 120 kN.m 3.0 m 30 kN C 3.0 m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Using double integration method, for the overhanging beam shown, (a) derive the equation of the…

A: Given data E = 29000 ksi I = 204 in4 1 ft = 12 inch 1 ft3 = (12)3 inch Lets solve using both…

Q: Using double integration method, determine the maximum deflection in the following beam and the…

Q: Problem 3 The bar CBA is axially loaded by force P at end A and by force Q at section B. The entire…

A: Given data, P = 4 kN E = 70 GPa Lab = 0.4 m Lbc = 0.5 m

Q: 1. Is the structure a truss or frame? Explain. 2. Which among the three methods may be applied in…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equ curve for…

Q: . For each member: A = 400 mm², E = 200 GPa. Use the Method of Virtual Work. a. Determine the…

Q: 100 kN -1.2 m 9'0

A: To find the vertical and horizontal displacement of joint D -

Q: The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi;…

Q: 80k (7.5) 10 (7.5) (4) (4) 20 20 (3)

Q: Exercise 2: Calculate deflection at B and slope at A.

A: The given question have to be solved by the virtual work method. In the question, the slope at point…

Q: use Castigliano's Method for Beams and Frames Determine the slope and the displacement at the end C…

A: Young's Modulus of elasticity (E) = 200 GPa Moment of Inertia (I) = 70 x 106 mm4 E I = 200 x 103 x…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Q: The cross sectional area of each member of the truss shown in the figure is A = 500 mm^2 and E = 200…

Q: What is the value of K so that the magnitude of the deflection at the middle of the two supports is…

Q: 1. For the beam section shown below, assume the section has cracked and say, the applied moment is…

Q: с a=1m P L= 3 m- B The deflection at point Cis I W150 x 18.0 15.6 mm. ↓

Q: ) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of…

Q: The flexural rigidity, EI, is constant from point A to point D. Use point A as the origin for the x…

A: Given:- EI = Constant To find:- a Slope at Ab Deflection at Bc Deflection at Cd Reaction at Ae…

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

Q: Using double integration method, for the overhanging beam shown, (a) derive the equation of the…

Q: 1. Compute the vertical and horizontal components of displacement of joint E produced by the loads.…

A: Given Area of AB,BD ,CD = 5 IN 2 All other = 3 in2 E= 30000 kips /in 2

Q: The box beam in the figure is made of four pieces of wood nailed to each other as shown.Since the…

A: Given- a= 16 b= 38 c= 32 d= 190 F= 160

Q: Two vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m.…

A: E=200GPa

Q: Use virtual work method. Find vertical displacement of joint B in mm due to a -2 mm fabrication…

A: ###Find vertical displacement of joint B in mm due to a -2 mm fabrication error on members BE and…

Q: a 2P B E FIGURE Q1 C a

Q: Each bar is made of steel and has a cross-sectional area of 600 mm. Take E = 200 GPa. 5. Determine…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: Problem #1: All the vertical bars are constructed from steel (E = 29,000 ksi and a = 6.5 x 10° 1/ºF)…

Q: The simply supported wood beam is loaded as shown. Ewood=10 GPa What is the slope at A? What is…

A: Determine the moment of inertia using the formula.

Q: 180 lb/ft 1350 lb-ft A + 9 ft ++ 9 ft →+ 9 ft 9 ft

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

Q: Using the method of virtual work, determine the VERTICAL displacement of joint C on the truss loaded…

A: Tension as taken as positive and compression as negative. When a member is connected with two hinge…

Q: Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.17 sq.in.…

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

Q: b a d

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

A: Truss: Truss is a pin jointed structure subjected to loading at joint only and the truss members…

Q: 3. A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the…

A: A Conjugate beam is an imaginary beam with and same geometrical properties as the real beam. The…

Q: The rod ABC is made of an aluminum for which E = 71.5 GPa. Knowing that P = 6.32 kNand Q = 46.66…

Q: own, use the double-integration method to determine (a) the equation of the elastic curve for the…

Q: Use VIRTUAL WORK METHOD to answer the questions below considering the truss shown in the figure.…

Q: concentrated load P = 6 kN, acting downwards, is located midway between the simple supports of the…

A: The given values are as follows, P=6kNa=6mE=233GPaI=253×106mm4To determine the deflection at C

Q: Determine the ff. using CONJUGATE BEAM method: • Slopes at A & D • Deflections at B & C 270 kN 180…

Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…

Q: Remove the distributed load w = 10.0 kN/m and determine the deflection of the beam at B due to the…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

100%

Determine the deflection and slope at A and C of the concrete beam in the figure using double integration method. Take E = 20.5 x 10^3 MPa and I = 6.75 x 10^8 mm^4. please show complete solution with drawing.

A
60 kN/m
2.0 m
B
120 kN.m
3.0 m
30 kN
C
3.0 m
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A concentrated load P = 5 kN, acting downwards, is located midway between the simple supports of the beam shown. Determine the deflection, in mm, at the free-end C. Use a = 6 m., E = 239 GPa, and I = 271 x10^6 mm^4. ROUND OFF TO THREE DECIMAL PLACES. USE STORED VALUES. INCLUDE THE SIGN OF YOUR FINAL ANSWER. (positive = upwards; negative = downwards) A a a
Problem 2. Use virtual work method and determine the following unknowns on the truss system shown below. Use A = 500 mm² and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. %3D a. Horizontal displacement of joint G due to the applied loads in mm b. Horizontal displacement of joint G considering that the top chord members experience 60 °C increase in temperature in mm. Use a = 10/ °C A=40.0 70 kN B=5.0 "a" kN C=9.0 50 kN "a" kN "c" m D 4 at "b" m
KAssignment 5 Problem 14.2 5 of 5 Consider the truss shown in (Figure 1). Take A = 0.0015 m² and E = 200 GPa for each member, and F = 17 kN Part A Determine the vertical deflection at joint (2 Express your answer to three significant figures and include the appropriate units. Enter negative value in the case when the deflection is downward and positive value in the case when the deflection is upward. ? Ay2 = 0.00077 Figure 1 of 1 Submit Previous Answers Request Answer F 4 m 4 m X Incorrect; Try Again; 11 attempts remaining 18 Part B 3 m 4 Determine the force in member 4 of the truss. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case
Use virtual work method. Use A = 500 mm2 and E = 200 GPa. a= 46 b= 4 c=11 Determine Horizontal displacement of joint G due to the applied loads in mm
The beam carries varrying load as shown. Determine the following. Use Double Integration Method in solving the required. 1. Deflection midway between the two supports 2. Deflection at the overhang akN/m 3m 5m
A Use the Castigliano's Method for Beams and Frames Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106) mmª. - 3m 29 KN D -3 m B + -3 m 4 kN Answers: •Displacement at C should be (87.75kN m³)/EI •Slope at C should be (23.25kN m²)/EI
2. Solve the following problem of bars in axial load using the finite element method, finding a) displacements at the nodes, b) reactions at supports, c) forces and stresses in each element. Consider E1=E2=E3=200GPa, A1= 20x10-4 m2, A2= 10x10-4 m2, A3= 8x10-4 m2 for the bars. F2= 40kN, F3= 50kN
A beam 2.4 m long is simply supported at two points A and B which are 1.44 m apart; point A is 0.36 m from the left-hand end of the beam and point B is 0.6 m from the right-hand end; the value of EI for the beam is 240×10® Nmm². Find the slope at the supports due to a load of 2 kN applied at the mid-point of AB. Use the reciprocal theorem in conjunction with the above result to find the deflection at the mid-point of AB due to loads of 3 kN applied at each end of the beam. Ans. 0.011, 15.8 mm.
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the beam at C. Assume a constant value of EI = 38 x 10^6 lb-ft^2 for the beam; w0 = 6800 lb/ft, LAB = 2.5 ft, LBC = 5 ft, LCD = 3 ft.
number 14
Consider the steel truss shown to answer Parts A, B, and C below, where P1 = 36 kN and P2 = 46 kN . The cross-sectional area of each member is A = 400 mm2 , E = 300 GPa, and ΔDh = 3.08 mm ΔEv = ____ mm
Give me right solution according to the question