A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: O a. 0.42 b. 0.61 c. 0.79 d. 0.57 It is the densification of soil by removal of air which require mechanical energy. Select one: a. solidification b. consolidation c. compression d. compaction What particular sand is ideal for field density test using sand cone method? Select one: O a. clean sand b. Ottawa sand c. Owatta sand d. white sand

A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: O a. 0.42 b. 0.61 c. 0.79 d. 0.57 It is the densification of soil by removal of air which require mechanical energy. Select one: a. solidification b. consolidation c. compression d. compaction What particular sand is ideal for field density test using sand cone method? Select one: O a. clean sand b. Ottawa sand c. Owatta sand d. white sand

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.12P

See similar textbooks

Similar questions

A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: a. 0.79 b. 0.57 c. 0.61 d. 0.42
Find the C, and the "apparent" OCR for a superficial clay stratum that is 4m thick. The water is at the surface. A sample of the clay has a water content of 27.9%, and a specific gravity of 2.65. An oedometer test showed the following results: Voids Ratio 0.736 0.733 0.73 0.675 0.638 0.6 Vertical Effective Stress 15 28 60 230 480 930
During the shearing phase of a CU test, the void ratio of a NC consolidated clay specimen will: 1decrease. 2could increase or decrease. 3remain a constant. 4increase.
A SAMPLE OF DRY SAND HAVING UNIT WEIGHT OF 16.50KN/m3 AND A SPECIFIC GRAVITY OF 2.70 IS PLACED IN THE RAIN. DURING THE RAIN THE VOLUME OF THE SAMPLE REMAINS CONSTANT BUT THE DEGREE OF SATURATION INCREASES TO 40% DETERMINE THE VOID RATIO IN PERCENT * DETERMINE THE WEIGHT OF THE SAMPLE AFTER BEING PLACED IN THE RAIN * THE WATER CONTENT OF THE SAMPLE AFTER BEING PLACED IN THE RAIN
Please give me right solution according to the question. In a triaxial test on a saturated clay, the sample was consolidated under a cell pressure of 160 kPa. After consolidation the cell pressure was increased to 350 kPa, and the sample was then failed under undrained condition. If the shear strength parameters of the soil are c’ = 15.2 kPa, ϕ’ = 26°, B = 1, Af = 0.27, determine the pore pressure at the failure.
A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, E₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (su). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.
The coefficient of permeability of sand at a void ratio of 0.80 is 0.47 mm/s. Estimate the coefficient of permeability of this sand at a void ratio of 0.50.
A CID TXC test was performed on a sample of sand. At the end of consolidation, the back pressure was 140 kPa, and the cell pressure was 340 kPa. At failure, the deviator stress was (ơ1 – 03)f = 200 kPa. a. What was the total pore water pressure, u, at failure? b. Calculate the principle effective stresses, ơi' and os', at failure. c. Calculate the friction angle, d', for this soil.
During an oedometer test on a specimen of saturated clay, the thickness of the specimen decreased from 19.931 mm to 19.720 mm under an increment of stress from 200 to 400 kPa which was maintained for 24 hours. The stress was then removed from the specimen, its thickness was measured as 19.842 mm, and its water content determined as 26.8%. Taking Gs of the particles to be 2.7o, calculate the void ratio before and after the application of the stress increment, and the coefficient of volume decrease (m,) for this stress range. (Ans: e;= 0.731, e2= 0.713, m, = 0.052 m/MN)
The table below contains data obtained from 2 CU triaxial tests on similar clay specimens. Specimen no. Cell pressure during consolidation (kPa) Deviatoric stress at failure (kPa) 269 Pore water pressure at failure (kPa) 264 400 379 1 2 462 689 Calculate the cohesion, c (kPa) of the clay soil in terms of total stress. Enter answer to 1 d.p. and don't enter units.