A round vertical steel tank has an inside diameter of 3 m and is 6 m in height. It contains gasoline with a density of 750 kg/m3 . If the allowable tensile stress is 25 Mpa, find the minimum thick required. A. 2.65 mm B. 2.85 mm C. 3.65 mm D. 1.82 mm Please solve ellaborately and include the Units. Thanks!

A round vertical steel tank has an inside diameter of 3 m and is 6 m in height. It contains gasoline with a density of 750 kg/m3 . If the allowable tensile stress is 25 Mpa, find the minimum thick required. A. 2.65 mm B. 2.85 mm C. 3.65 mm D. 1.82 mm Please solve ellaborately and include the Units. Thanks!

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take maximum tensile stress for cast iron as 14 MPa. [Ans. 6.25 mm]
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
Determine the value of load P if At = 30 °C and the stress in bronze is limited to 132 MPa. Aluminum Bronze A = 600 mm? A = 500 mm? L= 2.0 m L= 2.50 m E = 70 GPa a = 23x10/ °C E = 83 GPa a = 18.90x10/ °C |c B D A O 2.0 m 3.0 m 1.0 m
A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box) Bronze Alum 850 1500 Ain mm E in GPa 70 83 bronz alum bronze
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
The aluminum machine part is subjected to a moment of 75 kNxm. Determine the bending stress created at points B and C on the cross-section and determine the maximum tensile and compressive bending stress in the part 10 mm 20 mm 10 mm 20 mm 10 mm 10 mm 10 mm A 40 mm M = 75 N·m
Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 °C. Use the following data: A (mm?) a (C) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10- 70 Copper unusunjv Copper 750 mm-
A l-m long steel bar (E = 200 GPa) of 10 x10 mm dimension fixed at one end and free at the other end is heated to 90°C from initially 30°C. What is the normal stress, in MPa, induced in the system đue to change in temperature? Use a = 12 x 10-6 per °C. Encode you answer in whole number. Round your answer to 0 decimal places. Add your answer A 5 cm diameter steel suspension cable fixed at the upper end with length 20 m is subjected to load P = 5 kN at its lowest end. If the cable weighs 7850 kg per cum and modulus of elasticity is 200 GPa, what is the deformation of the cable due to the applied P alone in mm? Round your answer to 2 decimal places. Add your answer
ASTEEL ܢܢܝܝܘ ܗ 25 KN ACOPPER a STEEL 2.8 m 3.6 m Three vertical rods of equal distance, each has a diameter of 20mm and supports a load of 25 KN as shown in the figure. Initially, all the rods are adjusted so that they share equal stresses. Neglecting any chance of buckling, and taking Es = 205 GPa and Ec = 100 GPa, determine the final stress in the steel when a further load of 20 KN is added.
A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box)