A round aluminum [E = 70000 MPa] rod must be designed for the following specifications: (a) The rod must be 2.28 m long. (b) The rod must carry a tensile load of 718 kN. (c) The normal stress in the rod must not exceed 160 MPa. (d) The rod must not elongate more than 5 mm. Determine the minimum diameter that can be used for the aluminum rod.

A round aluminum [E = 70000 MPa] rod must be designed for the following specifications: (a) The rod must be 2.28 m long. (b) The rod must carry a tensile load of 718 kN. (c) The normal stress in the rod must not exceed 160 MPa. (d) The rod must not elongate more than 5 mm. Determine the minimum diameter that can be used for the aluminum rod.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.
What is the force effect
please put it on paper. thank you
What are crumple zones in cars designed for? O absorbing the shock from bumpy roads changing the direction of the car during impact increasing the time it takes for a car to stop during a crash allowing the car to be scrapped and recycled easily
please provide a clear solution and FBD. please answer within 30 minutes, thank you!
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…
Te-Learning Portal Courses Reports e-Services Which of the following statement is correct Select one: of O Fiction is very bad at rough surfaces ion O Friction is zero for smooth surfaces O Friction is good at smooth surfaces O Friction is high for rough surfaces
Q2 For the beam section as shown in Fig. Q2, determine the following: a) X, the location of its centroid along x-axis b) Y, the location of its centroid along y-axis
kindly create a conclusion regarding Tesla Cars and its factory
Please do it quickly i have one hour and have thank you for helping
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
use this logo and explain for saftey