A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?

A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.1P

See similar textbooks

Similar questions

To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads do I need to apply? (b) What is the maximum length of this sample without plastic deformation? How long can it be extended? (The modulus of elasticity of steel is 210 GPa, yield strength 580 MPa, tensile strength 920 MPa specified as.
An aluminum alloy bar with a rectangular cross section that has a width of 12.5 mm, thickness of 6.25 mm, and a gauge length of 50 mm was tested in tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in Table P4.6. Using a spreadsheet program, obtain the following: a. A plot of the stress-strain relationship. Label the axes and show units. b. A plot of the linear portion of the stress-strain relationship. Determine the modulus of elasticity using the best fit approach. c. Proportional limit. d. Yield stress at an offset strain of 0.002 m/m. e. Tangent modulus at a stress of 450 MPa. f. Secant modulus at a stress of 450 MPa. TABLE P4.6 Load (kN) AL (mm) Load (kN) AL (mm) 33.5 1.486 3.3 0.025 35.3 2.189 14.0 0.115 37.8 3.390 25.0 0.220 39.8 4.829 29.0 0.406 40.8 5.961 30.6 0.705 41.6 7.386 31.7 0.981 41.2 8.047 32.7 1.245
A round aluminum alloy bar with a 0.25-in. diameter and a 1-in. gauge length was tested in tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in Table P4.8.Using a spreadsheet program, obtain the following: a. A plot of the stress–strain relationship. Label the axes and show units. b. A plot of the linear portion of the stress–strain relationship. Determine modulus of elasticity using the best fit approach. c. Proportional limit. d. Yield stress at an offset strain of 0.002 in/in. e. Initial tangent modulus. f. If the specimen is loaded to 3200 lb only and then unloaded, what is the permanent change in gauge length? g. When the applied load was 1239 lb, the diameter was measured as 0.249814 in. Determine Poisson’s ratio.
A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.1 mm and the diameter was changed to 9.9967 mm,calculate the modulus of elasticity and Poisson’s ratio.
A cylindrical specimen of stainless steel having an initial diameter of 12.8?? and initial length of 50.8?? is pulled in tension. Use the data provided below to a) Plot the data as engineering stress versus engineering strain using excel or similar software. b) Compute the modulus of elasticity. c) Determine the yield strength at a strain offset of 0.002. d) Determine the tensile strength of this alloy. e) What is the approximate ductility, in percent elongation? f) Compute the modulus of resilience. Load (?) Length (??) 0 50.800 12,700 50.825 25,400 50.851 38,100 50.876 50,800 50.902 76,200 50.952 89,100 51.003 92,700 51.054 102,500 51.181 107,800 51.308 119,400 51.562 128,300 51.816 149,700 52.832 159,000 53.848 160,400 54.356 159,500 54.864 151,500 55.880 124,700 56.642 Fracture
The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.
A cylindrical rod with a diameter of 15.24 mm and a gauge length of 400 mm is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.45 mm when the applied load is 31000 N, which of the four metals or alloys listed below are possible candi- dates? Justify your choice(3). TABLE P1.12 Material E (GPa) Yield Strength (MPa) Tensile Strength (MPa) Steel alloy 1 Steel alloy 2 Titanium alloy Сopper 180 860 502 200 400 250 110 900 730 117 220 70
A cylindrical rod 360 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load. If the rodis to experience neither plastic deformation nor an elongation of more than 0.9 mm when the applied load is22500 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).Material Modulus ofElasticity (GPa)Yield Strength(MPa)TensileStrength (MPa)Aluminum alloy 70 255 420Brass alloy 100 345 420Copper 110 210 290Steel alloy 207 450 550
A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile load. The rod must not experience plastic deformation or an increase in length of more than 0.9 mm when a load of 24.5 kN is applied. Which of the four materials listed in table are possible candidates? Justify your answer. Material Elastic Modulus, GPa Yield Strength, MPa Tensile Strength, MPa 110 ETT 70 207 101 Copper Aluminum alloy Steel Brass alloy 248 255 448 345 289 420 551 420 * Plastic deformation is defined as a process in which the object due to applied force changes its size or shape in a way that is not reversible
hree steel bars with a diameter of 25 mm and carbon contents of 0.2, 0.5, and 0.8%, respectively. The specimens were subjected to tension until rupture. The load versus deformation results were as shown in Table P3.19. If the gauge length is 50 mm, determine the following: The tensile stresses and strains for each specimen at each load increment. Plot stresses versus strains for all specimens on one graph. The proportional limit for each specimen. The 0.2% offset yield strength for each specimen. The modulus of elasticity for each specimen. The strain at rupture for each specimen. Comment on the effect of increasing the carbon content on the following: Yield strength ii. Modulus of elasticity iii. Ductility
Testing a round steel alloy bar with a diameter of 15 mm and a gauge length of 250 mm produced the stress-strain relationship shown in Figure P3.28. Determine a. the elastic modulus b. the proportional limit c. the yield strength at a strain offset of 0.002 d. the tensile strength e. the magnitude of the load required to produce an increase in length of 0.38 mm f. the final deformation, if the specimen is unloaded after being strained by the amount specified in (e) g. In designing a typical structure made of this material, would you expect the stress applied in (e) reasonable? Why? 750 500 250 0.01 0.02 0.03 0.04 Strain, m/m FIGURE P3.28 Stress, MPa
1.19 A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy 12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm. On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If so, calculate the load. If not, explain why.