A rigid block of mass M is supported by three symmetrically spaced rods as shown in the figure. Each copper rod has an area of 900 mm²; E = 120 GPa; and the allowable stress is 70 MPa. The steel rod has an area of 1200 mm²; E = 200 GPa; and the allowable stress is 140 MPa. Determine the largest mass M which can be supported. Copper Steel 160 mm 240 mm T Copper 160 mm

A rigid block of mass M is supported by three symmetrically spaced rods as shown in the figure. Each copper rod has an area of 900 mm²; E = 120 GPa; and the allowable stress is 70 MPa. The steel rod has an area of 1200 mm²; E = 200 GPa; and the allowable stress is 140 MPa. Determine the largest mass M which can be supported. Copper Steel 160 mm 240 mm T Copper 160 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
A steel rod with a cross sectional area of 120 (mm) ^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? a=11.7x [10] ^(-6)/°C and E = 200GPA. See figure 06. * Figure 06 120 MPa 130 MPa 140 MPa 150 MPa
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
1.17 Figure P1.17 shows the stress-strain relations of metals A and B during tension tests until fracture. Determine the following for the two metals (show all calcu- lations and units): a. Proportional limit b. Yield stress at an offset strain of 0.002 in./in. 150 - - Metal A 100 • Metal B 50 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 Strain, in./in. FIGURE P1.17 c. Ultimate strength d. Modulus of resilience e. Toughness f. Which metal is more ductile? Why? Stress, ksi
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
A l-m long steel bar (E = 200 GPa) of 10 x10 mm dimension fixed at one end and free at the other end is heated to 90°C from initially 30°C. What is the normal stress, in MPa, induced in the system đue to change in temperature? Use a = 12 x 10-6 per °C. Encode you answer in whole number. Round your answer to 0 decimal places. Add your answer A 5 cm diameter steel suspension cable fixed at the upper end with length 20 m is subjected to load P = 5 kN at its lowest end. If the cable weighs 7850 kg per cum and modulus of elasticity is 200 GPa, what is the deformation of the cable due to the applied P alone in mm? Round your answer to 2 decimal places. Add your answer
What will have more strain, a 10ft bar being stretched 3 inches or a 3ft bar being stretched 3 inches? It depends on the material The 3ft bar It depends on the area The 10ft bar 000 0
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft