A rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m °C) for steel and 18.9 um/(m °C) for bronze. -1m Steel L = 1.5 m A=320 mm² E = 200 GPa 2.5 m Bronze L-3m A = 1300 mm² E = 83 GPa W 1.5 m

A rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m °C) for steel and 18.9 um/(m °C) for bronze. -1m Steel L = 1.5 m A=320 mm² E = 200 GPa 2.5 m Bronze L-3m A = 1300 mm² E = 83 GPa W 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature. Brass L=2 m A= 1200 mm E= 100 GPa a = 18,7 x 10-y°C B -2 m Соpper L=3 m A = 1500 mm E= 120 GPa a = 16.8 x 10-bj°C FIG. P2.108
The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in) a (PF) E (GPa) Steel Rod 300 11.7 x 104 200 Bronze Rod 1400 18 x 106 83 Bronze 3 m Steel 1.5 m 1.0 m 2.5 m 1.5 m W
A circular bar of magnesium alloy is 390 mm long. The stress-strain diagram for the material is shown in the figure. 70 63 56 49 O (MPa) 42 35 28 21 14 7 0.002 0.004 0.006 0.008 0.01 The bar is loaded in tension to an elongation of 2.34 mm, and then the load is removed. Hint: Use the concepts illustrated in the figures below. (Assume the curve in the figure above is linear between (0, 0) and (0.001, 28), and curves with a gradually decreasing slope otherwise.) F В E F Loading CD Loading Residual Elastic strain recovery (a) What is the permanent set of the bar (in mm)? 2.184 X mm (b) If the bar is reloaded, what is the proportional limit (in MPa)? 55 X MPa
Knowing that a 0.03-in. gap exists when the temperature is 85 °F, determine the temperature at which the normal stress in the aluminum bar will be equal to-11 ksi. T= OF 0.03 in. 12 in. Bronze A = 2.2 in.² E = 15 × 106 psi a = 12 x 10-6°F 16 in.. Aluminum A = 2.8 in.² E = 10.6 × 106 psi a = 12.9 × 10 6 °F Ans = 250
Q:A rigid block of negligible mass is supported by three rods as shown in figure, if a load (P) is subjected to the block, find the stress in the steel and aluminum rods. The area in addition to the properties of each material are given in Table below: E, Ea A, Aal A(mm) (mm) (Gpa) (Gpa) (mm') (mm') (kN) (Gра) 500 0.1 190 80 800 1600 1200 Steel Steel
d) Calculate the change in temperature. Indicate increase or decrease in temperature.
Please answer it properly don't waste my question I will vote it up for your effort thank you.
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C P Steel: A-900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0 m E = 200 GPa L=1.5m What is the value of P without exceeding the allowable stress of bronze, in kN? O 161 O 174 O 145 124 4
The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in?) a (/°F) E (GPa) Steel Rod 300 11.7 x 106 200 Bronze Rod 1400 18 x 10-6 83 Bronze 3 m Steel 1.5 m 1.0 m 2.5 m 1.5 m W
The assembly shown in the figure consists of an aluminum tube AB and a steel rod BC. The rod is attached to the tube through the rigid collar at B and passes through the tube. The cross-sectional area of the rod is 75 mm2 and the cross-sectional area of the tube is 400 + UV in mm2, where UV is 99. A tensile load of 80 kN is applied to the rod. Take Est = 200 GPa for the steel rod, Eal = 70 GPa for the aluminum tube. Determine: (a) the displacement of end C with respect to end B (i.e., the elongation of the steel rod), (b) the displacement of end B with respect to the fixed end A (i.e., the shrink of the aluminum tube), (c) the displacement of the end C of the rod (i.e., (a) + (b)).
Determine the maximum shearing stress developed in aluminum. Determine the maximum shearing stress developed in steel. Determine the maximum shearing stress developed in bronze.
The state of stress at a certain point in a stressed body is as shown in the figure. Normal stress in x-direction is 80 MPa (Tensile) and in y-direction is 40 MPa (Compressive). The radius of the Mohr's circle for this state of stress will be O, = 40 MPa O, = 80 MPa + Ox = 80 MPa Oy = 40 MPa (а) 60 MPа (b) 40 MPa (c) 20 MPa (d) 10 MPa