Knowing that a 0.03-in. gap exists when the temperature is 85 °F, determine the temperature at which the normal stress in the aluminum bar will be equal to-11 ksi. 0.03 in. Bronze 12 in. 16 in. Aluminum

Knowing that a 0.03-in. gap exists when the temperature is 85 °F, determine the temperature at which the normal stress in the aluminum bar will be equal to-11 ksi. 0.03 in. Bronze 12 in. 16 in. Aluminum

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6 A steel pipe with a 50 mm outside diameter and a 43.75 'mm inside diameter surrounds a solid brass rod 37.5 mm in diameter as shown. Both materials are joined to a rigid cover plate at each end. The assembly is free to expand longitudinally. The assembly is stress free at a temperature of 27°C. For steel, Young's modulus is 200 GN/m², and the coefficient of linear thermal expansion is 11.7x10-6 1/°C. For brass, Young's modulus is 93.33 GN/m², and the coefficient of linear thermal expansion is 1.872 x 10-5 1/°C. What is the stress in the steel tube when the temperature is raised to 121°C? brass rod (solid) 37.5 mm diameter steel tube 50 mm outside diameter 43.75 mm inside diameter
Two similar bars of Steel and Aluminium are heated to a same temperature. Forces are applied at the ends of the bars to maintain their lengths unaltered. If the ratio of Young's moduli of Steel and Aluminium is 3, and the ratio of the coefficients of thermal expansion of Steel to that of Aluminium is 0.5, what is the stress on the Aluminium bar if the stress on the Steel bar is 100 MPa?
79. A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius of 10 m by applying a pure moment M. If Young's modulus E = 200 GPa, then the magnitude of M is (1) 72 Nm (2) 144 Nm (3) 216 Nm (4) 288 Nm
A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and a = 12 × 10-6/°C. (a) 20 MPa (c) 68 MPa (b) 35 MPa (d) None of these
A steel bar is heated from room temperature to 80oC while it is free to expand. The bar will therefore be subject to: A. compression B. tension C. no stress D. shear
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. -14 in. 18 in. Aluminum A = 2.8 in² Bronze A = 2.4 in² E = 15 × 10º psi a = 12 x 10-6/°F E = 10.6 × 106 psi α = 12.9 x 10-6/°F Fig. P2.58 and P2.59
Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction. S11=7.6 (TPa)-', S12 = - 2.8 (TPa)-', S44 = 8.6 (TPa) -!
d) Find the stress (in psi) induced in the aluminum tube by the temperature change.
I5 In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in & total length 8 in) had a 0.2% offset yield strength of 80.000 psi and engineering strain of 0.010 at the yield strength point Calculate: The load (force) at this point. The instantaneous area of the specimen at this point. c. The true stress at this point. d. The true strain at this point. e. The total length of the specimen. if the load is released at this point.
Normal stress is calculated dividing the reaction by the cross-sectional area. Is this approach valid for any point of a structural member? Why or why not? To answer this question, consider the loading point, cross- sectional shape, etc.
the cross-sectional area of the bar 1 of the two bars supported on the left and right sides is 1.2 cm^2, the coefficient of thermal expansion is 20.9 10^(-6)/K; The cross-sectional area of bar 2 is 3 cm^2 and its coefficient of thermal expansion is 25.4 10^(-6)/K. Since the modulus of elasticity of the material is 207 GPa, these two bars are heated to 99 °C.a) What will be the change in length (mm) of bar 1?b) What is the stress in bar 1 in MPa?c) What is the stress in bar 2 in MPa?
A steel rod is fixed at one end and the other end has a distance of 0.2 mm from a rigid support. The rod is heated to increase its temperature by 200°C. Calculate the stress developed in the rod. The elastic modulus of rod is 200 GPa and the coefficient of thermal expansion is 104per °C.