A rigid bar AD is supported by a ball-and-socket at D, and the two cables are attached to the beam at A. A downward force of magnitude 5000 N is applied at A. Neglect the weight of the rigid bar AD. what is the magnitude of the tension AB, denoted by T1? And what is the magnitude of the tension AC, denoted by T2 АВ Let TR = T, АВ AB AC T2 Im C m 2 m 4 m 5000 N

A rigid bar AD is supported by a ball-and-socket at D, and the two cables are attached to the beam at A. A downward force of magnitude 5000 N is applied at A. Neglect the weight of the rigid bar AD. what is the magnitude of the tension AB, denoted by T1? And what is the magnitude of the tension AC, denoted by T2 АВ Let TR = T, АВ AB AC T2 Im C m 2 m 4 m 5000 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal rod of length L= 9.64 m is attached to an axel in such a way that the axel is located at its left end. Three forces are acting on the rod: F1= 11.6N at the location 2.59 m from the axel, F2 = 15.7 N at the location 5.02 m from the axel, and F3 =15.0 N at the laction 2.31 m from the axel. F1 (pointing up and to the right) makes an angel of 47.7 degrees with the rod, F2 (pointing up and to the left) makes an angel of 45.1 with the rod, and F3 points directly downwards. Calculate the net torque that these three forces exert on the rod. Also, indicate if the torque is clockwise it counter-clockwise.
บ T₂ /02 F T₁ ง 01 T In the diagram above, tension on two ropes, T1 and T2, causes the resultant force F = 58.9kN. Compute the value of T₁ if 0₁ = 30 deg and 02 = 27 deg.
Q1
Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In the position shown, a 18.86-kN horizontal force is applied to the bucket at point L. Assuming the weight of the backhoe arm is negligible compared to forces acting on it, find the force acting on pin A (FA) in kN.
Find the forces of members marked with x.
Be careful, you have only one question, for this problem. The pulling force is P = 545N. The direction of the rope B is defined by the angle 0-35deg. The position of the point D is (1.3,-2.3.3.1) Xo D Zo Y X P What is the tension Tc in N? Give your answer as an integer. o B -y
It was known that there are five members concurrent at joint A isolated in the figure below. Out of those five member forces, the magnitude and direction of three member forces are known and shown in the figure below. Calculate the remaining unknown member forces F1 and F2, so that equilibrium of forces is satisfied at joint A.
Consider the weight suspended by two wires in each diagram. Find the magnitudes and components of vectors F1 and F2, and angles a and b.
2- Find the applied force by the hydraulic cylinder in the truck shown graphically using KS: 1cm=1m, KF: 1cm=1 kN. W=25 kN
Two equivalent system of forces and moments act on the plate are shown in the figure below. Determine the force P. * 60 N 20 N 60 N 1.5m 1.5m D 1.6m E M. 200 Nm 60 N E 4m 4m 100 NI System 1 System 2
b) The steel Cable AB and AC are attached to the top of the transmission tower. The tension force in cable 40 m AC is 8 kN. Determine the required tension force in Cable AB, such that net effect of the two cable tensions is downwards force at Point A as shown in 20m the figure. Then determine the magnitude force R of these downwards forces? 00 m
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 24 ring Cable r= 0.5 m 30 0.5 m B 2 m 30 Figure (2)