A reducing elbow in a horizontal pipe is used to deflect water flow by an angle = 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 56 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. The density of water is 1000 kg/m3, and the flow rate of water is 30 kg/s.

A reducing elbow in a horizontal pipe is used to deflect water flow by an angle = 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 56 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. The density of water is 1000 kg/m3, and the flow rate of water is 30 kg/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reducing elbow is used to deflect water flow at a rate of 30 kg/s in a horizontal pipe upward by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into an atmosphere. The cross sectional area of the elbow is 150 cm² at the exist. The elevation difference between the centers of the exist and the inlet is 40 cm. The mass of the elbow and the water is 50 kg. Determine the anchoring force needed to hold the elbow in place. (Ans: 1.18 kN) 150 cm 40 cm Water
A reducing elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward 30°. The elbow discharges water into the atmosphere. The difference between the centers of the outlet and the inlet is 30 cm. The weight of elevation the elbow and the water in it is considered to be negligible. Determine the anchoring force (F) needed to hold the elbow in Rx place. Given that other force F acts on the elbow which is equal 500 N A=7 cm 2. A-113 cm 30 cm
6-23 A reducing elbow in a horizontal pipe is used to deflect water flow by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into the atmo- sphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 50 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum- flux correction factor to be 1.03 at both the inlet and outlet. 150 cm² Water 30.0 kg/s FIGURE P6-23 25 cm² 15- 40 cm
6-22 A 90° elbaw is used to direct water flow at a rate of 25 kgis in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03. 35 cm Water 25 kg/s
Water is flowing through a 15-cm-diameter pipe that consists of a 3-m-long vertical and 2-m-long horizontal section with a 90° elbow at the exit to force the water to be discharged downward, as shown, in the vertical direction. Water discharges to atmospheric air at a velocity of 5 m/s, and the mass of the pipe section when filled with water is 17 kg per meter length. Determine the moment acting at the intersection of the vertical and horizontal sections of the pipe (point A). What would your answer be if the flow were discharged upward instead of downward?
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50 g and is charged with 100 g of water. The pressure inside the rocket is 100 kPa gage. The exit area is one-tenth of the chamber crosssectional area. The inside diameter of the rocket is 5 cm. Assume that Bernoulli's equation is valid for the water flow inside the rocket. Neglecting air friction, calculate the maximum velocity it will attain. 5 cm PROBLEM 6.90 100 kPa
The adjacent picture shows a pipe section in which a reduction sleeve (nozzle) is connected to the pipe by a flanged bolted connection. You have D1=8 cm, D2=5 cm, and the water is at 20C. Point 2 is open to the atmosphere. Consider that the specific mass of the water is 1,000 kg/m3, and that the momentum flux correction factor is unity. If V1=5 m/s and the mercury manometer indicates that h=58 cm, determine the reaction force on the flange bolts.
H.W (03-03-2021): The rectangular duct section of 400mm*300mm size carries 50 m^3/min of air, with density 1.2 kg/m^3. Where the f=0.015 A- Determine the equivalent diameter of circular duct if: 1. when the quantity of air passing through the rectangular and circular ducts is same. 2. when the velocity of air passing through the rectangular and circular ducts is same. B- Determine the pressure loss per 75m length of rectangular duct. C- Determine the pressure loss per 75m length of equivalent diameter of circular duct, when the quantity and velocity of air passing through the restenulos anguler ond eiroulor ducts is same .
A three-arm sprinkler is used to water a garden by rotating in a horizontal plane. Water enters the sprinkler along the axis of rotation at a rate of 40 L/s and leaves the 1.2-cm-diameter nozzles in the tangential direction. The central sprinkler bearing applies a retarding torque of 50 N-m due to friction at the anticipated operating speeds. Part A For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the rate of rotation of the sprinkler. Express your answer to three significant figures. V ΑΣφ I1 vec ? W = rad/s Submit Request Answer
A ball weighing 1 kg is “floating" on a circular jet, as shown in the figure (ignore the wire, which is there to stabilize the weight). The jet leaving the orifice at the bottom has an upward velocity of 10 m/s, and the jet diameter at the exit is 2 cm. Assuming the jet spills sideways at 90°, find the height h at which the ball will float. Jet D1 =0.02 m W1 = 10 -
A jet of water flows from left to right and hits a splitter block, as shown in the figure. Some of the jet is diverted upwards and some of it downwards. The incoming jet has a velocity U1= 2 m/s and a cross-sectional area A1. The jet that is deflected upwards has a velocity U2= 0.6 m/s, a cross-sectional area A2= 11 cm^2 and is at an angle θ2= 15o with respect to the horizontal. The jet that is deflected downwards has a velocity U3= 0.9 m/s, a cross-sectional area A3= 9 cm^2 and is at an angle θ3= 40o with respect to the horizontal. The density of water is ρ=1000 kg/m^3.a) Find the cross-sectional area of the incoming jet (in cm^2)b) Find the horizontal force on the block (in Newtons) (Note: remember to convert the area of the jets from cm^2 to m^2) c) The vertical force on the block is found to be Fy. What velocity of the incoming jet (i.e. what value of u1) would be needed to generate a force of 4Fy? (Note that you don't need to actually find Fy to solve this question)
kg Water (p = 1000- -) flows through the elbow below. The diameter of both the inlet and outlet is 1.1 cm, and the velocity through the nozzle is V =4.5 m/s. The outlet m³ has an angle of 0 =15 degrees. The water is at a pressure of 29 kPa (gauge). Find the magnitude of the force on the elbow. 0 V