The rectangular duct section of 400mm*300mm size carries 50 m^3/min of air, with density 1.2 kg/m^3. Where the f=0.015 A- Determine the equivalent diameter of circular duct if: 1. when the quantity of air passing through the rectangular and circular ducts is same. 2. when the velocity of air passing through the rectangular and circular ducts is same.

The rectangular duct section of 400mm*300mm size carries 50 m^3/min of air, with density 1.2 kg/m^3. Where the f=0.015 A- Determine the equivalent diameter of circular duct if: 1. when the quantity of air passing through the rectangular and circular ducts is same. 2. when the velocity of air passing through the rectangular and circular ducts is same.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer with True or False of the following question: (7M 1. Water flows steadily down a vertical pipe of constant cross section. Neglecting friction, according to Bernoulli's equation, velocity decreases with height. 2. A liquid in an open right circular cylinder is given rigid body rotation about the axis of the cylinder. The pressure distribution in any vertical plane is uniform. 3. A curved surface is submerged in a static liquid. The horizontal component of pressure force on it is equal to the pressure force on a vertical projection of the surface. 4. A U-tube manometer measures the difference in total energy between two points.
4. Water is flowing in a pipe with radius of 25.4 cm at velocity of 5 m/s. The viscosity of water is 1.131 Pa-s and its density is equal to 997.9 What is its Reynolds m³° number and type of fluid flow?
two points; (D) gauge 10. A Terran T-280 SCV (space construction vehicle) examines a typical vespene geyser field, which normally contains 20 circular openings, each of which has a radius of 0.10 m. The geyser mouths (according to a sonar probe) are connected to a main geyser “pipe" 0.80 m in radius. If the speed of the vespene gas is 3.0 m/s through the main pipe, what is its velocity as it exits through one of the geyser mouths? spaads The
Q1: A water tower is an elevated structure supporting a water tank constructed at a height sufficient to pressurize a distribution system for potable water. A completely filled and pressurized water tank was found with a small leakage (a hole 5cm in diameter) located on the sidewall of the tank, around 5 meters below the top of the tank. Please calculate the velocity of leakage water that discharges to the normal atmosphere. The dimension of the tank is 20-meter in height and 10-meter in diameter. The gauge pressure of the water tank top is 0.1M Pa. The Bernoulli equation is: P₁/pg + V₁²/2g +h₁ = P₂/pg + V₂²/2g +h₂ Gauge Pressure: 0.1 M Pa 5 meters Leakage velocity?
H.W.2/: The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 m is filled with a liquid (SG > 1, like glycerin) and the rest with water, as shown in the figure below. The tank is now rotated about its vertical axis at a constant angular speed of v. Determine (a) the value of the angular speed when the point P on the axis at the liquid-liquid interface touches the bottom of the tank and (b) the amount of water that would be spilled out at this angular speed? 3h h = 0.1 m D = 0.3 m
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
A fluid is being pumped through a pipe. The density of fluid is 872 kg/m³. The viscosity is 2.8x102 Pa.s. The velocity in the pipe is 5.9 m/s. If the Reynolds number is 2100. a- What is the pipe cross-sectional area? b- If the pipe cross-sectional area increased 1.5 fold under same Reynold number, density and viscosity, what is the new velocity?
A vertical gap 2.2 cm wide of infinite extent contains a fluid of viscosity 2.0 N s/m? nd specific gravity 0.9. A metallic plate 1.2 m x 1.2 m x 0.2 cm is to be lifted up with a constant velocity of 0.15 m/sec, through the gap. If the plate is in the middle of the gap, find the force required. The weight of the plate is 40 N. F 1.0 1.0 cm cm 0.2 cm
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
Water flows through a 125 mm diameter pipe at a velocity of 7.5 m/sec. Find the mass flow rate in kg/sec. NOTE: Do not write any unit to your answer, put your answer in a numerical form only and use up to 3 decimal places. ASAP PLS
The Reynold’s number for fluid in a pipe of 10-in diameter is 2000. What will the Reynold’s number in a 6-in diameter pipe forming an extension of the 10-in pipe? Take the flow as incompressible.
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro