A rectangular beam has the dimensions b=12in., h=26in., and d=24 in. and is reinforced with three No. 11 bars so that As-4.68 in.². The normal-weight concrete compressive strength is 5000 psi. and the tensile strength (modulus of rupture) can be calculated as per ACI318-14. The Grade of the steel is 60. Determine the nominal moment strength M, and the moment capacity Mn. b=12 in. Figure 1. d=24 in. h=26 in.-

A rectangular beam has the dimensions b=12in., h=26in., and d=24 in. and is reinforced with three No. 11 bars so that As-4.68 in.². The normal-weight concrete compressive strength is 5000 psi. and the tensile strength (modulus of rupture) can be calculated as per ACI318-14. The Grade of the steel is 60. Determine the nominal moment strength M, and the moment capacity Mn. b=12 in. Figure 1. d=24 in. h=26 in.-

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension- controlled condition. Use the following dimensions: b = 498 mm d = 709 mm t = 152 mm web thickness - 152 mm b 1 I d
A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm2 at centre of gravity of the section. The pre-stress in the tendons is 1000 N/mm2.- Assuming modular ratio as 10, the stress (N/mm2) in concrete is
* The Dn value for a low relaxation steel is ______. * Determine the elastic shortening loss of a pretensioned concrete, in percentage (simply supported L=15m, H=900mm, B=300mm) given that, fpi=1100MPa, f'ci=40MPa, Eps=200GPa, and the total area of the straight profile tendons is 140 sq.mm.
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi