A prismatic bar has a cross-section of 25 mm by 50 mm and a length of 2000 mm. Under an axial load of 100 kN, the measured elongation of the bar is 2mm. The tensile stress and % strain in the bar are

Q: Length of beam=5m 6016mm 60 16 mm Section 1-11 WOZ 0.40 m-

A: We know that,  Volume = L×B× H Given,  Length of the beam = 5 m.  Width of the beam= 0.40 m.  Depth…

Q: Use of mild steel instead of stainless steel can prevent corrosion. Select one: True False

A: Mild steel is more prone to corrosion whereas stainless steel is actually the steel which has…

Q: Determine the moment of inertia of the composite area about the centroidal axis

A: The moment of inertia of the composite area about the centroidal y axis -  IY = IY1 -  IY2 +  IY3 +…

Q: It is acceptable to have threads in glass parts as long as such threads were coarse.   T or F

A: Threaded glass components are manufactured by a number of different companies in a variety of sizes…

Q: Part 2: Identify the read forces 4m 1) 60⁰ 4m 4m 10KN Rea'd: All member forces (use metheel of…

A: Given data in question  Load 10 kN Span member length   4m Angle 60° To find out  Member forces

Q: Determine the volume of material needed to make the casting.

A: Consider the following diagram and divide it into the areas

Q: in steel, explain effective length factors

A: Effective length factors (K-factor) are used in the analysis and design of steel structures to…

Q: The PVI is located halfway between the PVC and PVT. True False

A: In civil engineering or road design, the vertical alignment of a road or highway refers to its slope…

Q: Problem 12-Method of Sections 2m 2m 10 11 12 13 10

A:

Q: Plane a-a is called the D.

A:

Q: Part 2: Identify the read forces 4m 1) 60⁰ 4m 4m 10KN Rea'd: All member forces (use metheel of…

A: Given data  Find all member force using method of joint.

Q: Find (a) Ix 3 (b) Iy for the composite

A:

Q: -2 m 2 m 2 m 4 m 4 m

A: Locate the centroid of shaded area shown

Q: 4. The structure shown is hinged at A and C. Find the horizontal and vertical components of the pin…

A:

Q: Find the lim f6atx) -f(9) for fCx) = Jx - 3

A:

Q: How much load must be applied on the wood, with a clear span length of 2350mm, deflection of the…

A: Given:- The clear span length = 2350 mm  The deflection of the wood = 12.5 mm  The modulus of…

Q: Determine the nominal axial compressive strength of the members shown in the following figure.

A: We have to determine the value of Axial compressive strength of the member shown in the figure and…

Q: *9-60. Locate the centroid (x, y) of the composite area. 150 mm 100 mm -300mm

A: The centroid () of the composite area =?

Q: m+R-2J =

A:

Q: Evaluate: /8(x- 1)xdx (x2.

A:

Q: Q4: Determine the plastic centroid of the section in figure fc'=25mpa, Fy= 420 Mpa, d 60mm. 600 4020…

A: The plastic centroid is the the location of the resultant force produced by the steel and the…

Q: (in %, up to two decimal places) is outer diameters of 100 mm and 106 mm. respectively. The area…

A: Find area ratio of core cutter,Ar=?

Q: Mex Force 15 KN APPlied on nail what is The Max V If Spacing between Nail is 75cm ? 15cm 5cm 15cm…

A:

Q: Match the cross-sections with the appropriate object and cutting plane for the problems shown below.…

A: Engineering drawing

Q: Locate the center of mass (x̄, y̅, z̅) of the homogeneous block assembly.

A:

Q: A bolt is turned from  to when tightening down on it.Through what angle was the bolt turned?

A: Consider the bolt is turned from

Q: 3/1 1/2 W% ↓t Wo t Wo-

A:

Q: (1) 10" 12" 2" 5" 2" 2" 8" A992 steel &Mp= ?

A: Steel grade - A992  The tensile yield strength, Fy = 50 ksi A cross-section of a steel structure is…

Q: rt explanation

A: Slab formwork essentially supports the weight of the concrete during the curing process and when the…

Q: 9. Write the deflection equation. Place your answer in a box. 10. What is the deflection at the pin…

A: Solution_1

Q: Pin Roller Roller (Truss)

A:

Q: Select all true statements regarding the strength of nails in wood connections. The nail strength…

A: Nail strength depends on the elastic properties and modulus of elasticity not the specific gravity…

Q: True or FALSE ?? In the analysis of line welds, the variable Ju has dimensions of length cubed

A: For analysis of line welds loaded in torsion, the quantity Ju is used, which is the unit second…

Q: 3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

A:

Q: PoL=280* PL= 200k Please select the ligutest W12 A992 steel

A: Column: Structural columns are components that span the entire altitude of the structure as well as…

Q: INTERNAL FORCES – BEAM ACB d) Draw a diagram of member ACB with all external forces acting on it,…

A:

Q: increasing the length of the beams will *

A: In construction beams are horizontal, weight-bearing supports that span between columns or posts.…

Q: The main plate of a theodolite is divided into 1440 equal divisions. 60 division of the vernier…

A: Division of main plate = 1440 60  division of vernier is equal to 59 division of main scale To find…