(1) 10" 12" 2" 5" 2" 2" 8" A992 steel &Mp= ?
Q: 3. For the system shown below compute the a. Flow rate, (k = 1.1m/day) Pore pressure at point B b. 3…
A: Given Data Find 1. Flow rate, when K = 1.1 m/day 2. Pore pressure at point B.
Q: Determine whether the plate is ill-arranged, geometrically unstable, statically determinate,…
A:
Q: A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible…
A:
Q: 15 kN/m 6m 3m (b) 60 KN
A: Shear Force Diagram: The shear force diagram represents the shear forces acting on a beam at each…
Q: A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when…
A:
Q: For the girder in the figure, draw the influence lines for the reaction at I, the shear to the right…
A:
Q: A body of dimensions 1.5 m x 1.0 mx 2 m, weighs 1962 N in water. What is the weight of the body in…
A:
Q: Which of the following statements is true? O Engineers do not need to worry about the sustainability…
A: Sustainable development- Development that is sustainable is one that satisfies current needs without…
Q: Determine the normal force, shear force, and moment in the beam at points C and D. Point D is just…
A:
Q: For the shown beam, determine the support reactions at pin A & roller B 600 lb/ft A 6 ft- B 3 ft-…
A: Given: A simply supported beam with one side overhanging where hinge at A and roller support at B.…
Q: The common tangent AB of a compound curve makes an angle with the tangents of the compound curve of…
A: Given,∆1=28°∆2=36°Stationing of V=12+434.63D1=5.6D2=3.6to determine,a) Radius of the simple curve…
Q: Write the V and M equation of the beams loaded as shown and the diagram. Then repeat the method…
A:
Q: Determine the support reactions of the beam shown. Use Slope Deflection Method (Indeterminate Beams)…
A: Given:
Q: 12. Refer to Figure II-1 attached. A flexible pavement is to be evaluated according to the AASHTO…
A: W have to find out the approximated number of daily equivalent 18-kip axles to be allowed on this…
Q: Determine the common tangent of a reversed curve given the following prop 11 = 15.26° D₁ = 4.98° 12…
A:
Q: 3. For the statically indeterminate cantilever beam (EI is constant) shown in Figure 3 and using…
A: Given Propped cantilever beam with point load acting on it. Length=3mLoad,P=25 kNEI=10*106 N-m2…
Q: Write the V and M equation of the beams loaded as shown and the diagram. Then repeat the method…
A:
Q: 10 ml of wastewater is diluted to 1 liter, aerated, and sealed. The initial dissolved oxygen level…
A: Given that,Volume of waste water,Vs = 10 mlIt is diluted to 1 liter aerated and sealed.Initial…
Q: 9. For the three-hinged arch shown, determine the reactions at A and B. The vertical distance…
A:
Q: A hydraulic jump takes place in a horizontal channel with sequent depths of 0.25 m and 1.5 m at the…
A:
Q: 4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The…
A: Given: Section: W 410 x 46.1 fc = 35 MPa A36 steel: fy = 250 mm fu = 450 MPa
Q: An office building is to be supported on a series of 1.8-m diameter, 18.0-m long solid pipe pile…
A: Given: D = 1.8 m L = 18 m F.O.S = 2.5 To find: The allowable downward capacity of the driven pile.
Q: 9.6 For the beam of Problem 8.10, determine the maximum pos- itive and negative shears and the…
A: Given: Concentrated live load= 150KN UDL Live load = 50 KN/m UDL dead load = 25KN/m Required:…
Q: 1. The common tangent AB of a compound curve makes an angle with the tangents of the compound curve…
A:
Q: A container of volume 3 x 103 m³ weighs 10 N. Dry sand was poured to fill the container. The…
A:
Q: Figure n°3 represents two walls of a low building but connected with a very long slab. The owners…
A: Solution: Note: Since the material used in the construction of the given wall is not given, it is…
Q: c) Show the computed shear and over-turning moment on the following graphs. FR F5 F4 F3 F2 BASE…
A: Here, It is given the computed data of building base shear and Overturning moment at Base of the…
Q: Why did you use 4000 when checking here 107170 > 4000?
A: This question is related to Open channel flow from fluid mechanic in civil engineering. This is…
Q: A triangular channel in a road median is transporting a runoff flow of 7.3 CFS, with a channel slope…
A: Given: FlowQ=7.3 CFS Channel slopeS=0.012 Manning's roughnessn=0.048 Side slope of channel(1 : z)=1…
Q: Describe in detail how a waste pipe size is calculated
A: Waste pipe sizes are available at different sizes that are used for the different plumbing uses.
Q: From the given truss, find the force of member CH, Load 1 = 30 kN, Load 2 = 60 KN Solve this using…
A:
Q: In a railroad layout, the centerline of two parallel tracks are connected with a reversed curve for…
A:
Q: A body of dimensions 1-5 m x 1.0 mx 2 m, weighs 1962 N in water. What is the weight of the body in…
A: Given- Dimension of the body- 1.5 m×1.0 m×2 m, Apparent weight-Wapparent=1962 N,g=9.81 m/s2 It is…
Q: Question- An instrument was setup at P and the angle of depression to a vane 2m above the foot of…
A: Given data, Distance between station = 3000 m R.L of P = 436 m Staff reading at p = 2.865 m
Q: The difference of water level between the upstream and downstream side of sheet pile of length 9 m…
A:
Q: A flat plate of 0.15 m² is pulled at 20 cm/s relative to another plate. fixed at a distance of 0.02…
A: Given- Area A=0.15 m2, Velocity V=20 cm/s, Distance=0.02 cm, It is needed to find the power required…
Q: A 3 m long simply supported beam of uniformcross section is subjected to a uniformlydistributed load…
A: Given: Length of the beamL=3m Flexural rigidityEI=30×106 Nm2 Uniformly distributed loadw=20 kNm To…
Q: 1. Determine the force in each member of the truss shown In Figure 1. Use method of Joints. State…
A:
Q: 6. Draw the shear and bending moment diagrams of the beam loaded as shown in the figures below.…
A:
Q: Explain why indoor air pollution levels can be much higher than ambient levels.
A: Air Pollution: The contamination of air due to atmospheric pollutants or any other pollutants in the…
Q: The jib crane is designed for a maximum capacity of 15 kN, and its uniform I-beam has a mass of 220…
A: Given that,Capacity of the jib Crane = 15 KN. Mass of the crane beam, M = 220 kg. Operating range…
Q: -25 kN/m 13 m 75 kN 3 m 4m B
A: Shear Force Diagram: The shear force diagram represents the shear forces at each point on the beam.…
Q: Determine the moments of inertia I, and I, of the area shown about vertical and horizontal axes…
A: Given: From the figure, Width of flangesB=120 mm Thickness of flangest=30 mm Overall depthD=180 mm…
Q: Consider the given figure. Given: P = 29 kN. 24 KN PKN 8 KN 8m 3m 24 m B Determine the maximum value…
A:
Q: 28. The PCA rigid pavement design chart for a B-777-300 aircraft is shown in Figure 7.7.3 attached.…
A: We have to find out the pavement thickness.
Q: 2.F6 A container of mass m = 120 kg is supported by three cables as shown. Draw the free- body…
A: The given of a conatiner suppoted by three cablle and we have to find out the tension foce iin each…
Q: Mr. Burns is having a new convenience store built on the southwest corner of Maple Drive and 3rd…
A: Given, Construction project situation
Q: From the following cross-section notes, complete the table below. Use prismoidal method. Road bed…
A:
Q: Question 2 In a laminar Poiseuille flow between two parallel plates, the ratio of average velocity…
A: Given data: Two horizontal parallel plates are spaced, H = 1 m μ=0.4 Nsm SG=0.9 Mean velocity,…
Q: A 3 m long simply supported beam of uniformcross section is subjected to a uniformlydistributed load…
A:
Step by step
Solved in 3 steps with 1 images
- A76 x 76 x6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy-248MPA and Fu -400MPA. Gusset Plate Alowable Sresse Alowable tensle stress igross ara)0.00 Alowable tereile stres net area)0SOF. Allowable shear stress (net ares)0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85% O 138.24 KN O 140.14 kN O 157.93 kN O 304.00 N NextI the Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf=120mm d=550mm d'=80mm fc'=34MPA fy=415MPA USE NSCP 2015 mm2 A.Mu = 1400KN-m, As = mm2 B.Mu = 1700kN-m, As = mm2, As' = CS Scanned with CamScannersted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
- أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):A For the truss shown, find veyticat deflection bylunit lead Methed. EA 15 _atfd) Ioku for all members increase in temp is (50€) in (ad) short in (ad)is (3 EmfrO 88 130% v - + I Annotate T| Edit Trial expired Unlock Full Version ENGR 263 + A A A T O 4.10 Member AB is the beam under consideration. As shown in the illustration of the loading condition, member AB is an overhanging beam that supports a uniformly distributed roof load of 500 lb/ft. It also carries concentrated loads from a rooftop HVAC unit (4000 lb), an interior hanging display support (2000 lb), and a marquee sign (3000 lb). Marquee overnang Displau SLIPPort II Raof Kiots Ol I W = 500 Ib/Ft A B 4000 b 2000 000 I Steel beam !! I1 3 FE 5 FE - Ft RoOFtop HVAC unit 10 FE 4 Ft Marquee sign< R R2 Steel beam (negligible weight) Free-body diagram Dispiay Support Loading condition
- Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ 子c D. 4 B AC BD IF IDPlz do not use gpt if u use chatgpt i will downvote you again don't use chatgptDETERMINE THE CENTROIDAL MOMENT OF INERTIA OF THE BUILT-UP SECTION SHOWN USING A STEEL PLATE 1"X16" AND C-12X25 STEEL SECTION WELDED TOGETHER. REFER TO THE TABLLE BELOW FOR THE PROPERTIES 12 Type EDSM Nomenciature AISC Manual Label C15X50 14.7 3.72 3.52 3.40 15.0 8716 0.799 404 11.0 17 C1SK40 C15X40 118 10.0 150 0520 0.400 0510 0650 0.650 0.501 0.501 0.501 0.778 348 315 C15K339 15.0 120 0.788 .07 C1200 C12X25 C12207 C1200 8.01 7.34 3.17 0.674 162 5.12 C1228 C12207 12.0 3.05 234 0.674 144 445 12.0 0.282 129 3.05 1. Determine Ixx (Centroidal) Not in the choices [Select] 1987.6 2. Determine lyy (Centroidal) 1642.67 Not in the choices 1612.7 1752.5
- There is a statically indeterminate beam in which the horizontal force at the left and right ends (points A and D) is zero, and the vertical force is shown in the figure below, The flexural stiffness of the beam section is constant El: Try to find the slope (Slope) of point B after deformation.A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L. C. = 31mm 16A (100 x 75 x 8) mm Choose the nearest correct statements: L1 = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mm7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92