A nozzle is fastened to the end of a U-tube with dimensions as shown in Figure Q2c. The nozzle exhausts into atmospheric pressure at 100 kPa; neglect friction and compute the force exerted on the U-tube by the water. If the force required to hold the nozzle is 850 N, determine the inlet pressure. 5 CRN 31896 V = 1 m/s 1 cm diameter 5 cm diameter

A nozzle is fastened to the end of a U-tube with dimensions as shown in Figure Q2c. The nozzle exhausts into atmospheric pressure at 100 kPa; neglect friction and compute the force exerted on the U-tube by the water. If the force required to hold the nozzle is 850 N, determine the inlet pressure. 5 CRN 31896 V = 1 m/s 1 cm diameter 5 cm diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

37. For a tank (T = 41 C°, volume = 0.051 m³, the rate change of density = 2.6 kg-m3-s*), through a hole of 0.36 cm?, v = 350 m-s1, calculate the pressure in the tank.
Q2: Water is flowing through an inclined pipe and two sections (section 1 and section 2) of the pipe are considered. The diameter of the pipe at section 1 is (240 + x) mm and (150 +x) mm at section 2. The elevations of the sections 1 and 2 above datum are (750 + x) cm and (350 + x.) cm respectively. If the pressure at section. 1 is 45 x10* N/m? and the discharge through the pipe is 65 litres per second, calculate the intensity of pressure at section 2. x=23
Consider a geyser that shoots water to a height of 28 m into the air.Density of water, rho = 1000 kg m-3, acceleration due to gravity, g = 9.81 ms-1, atmospheric pressure, Patm = 101250 Pa. How fast is the water traveling when it emerges from the ground, If the water originates in a chamber 44 m below the ground, what isthe pressure there (consider there is NO friction within the chamberand that the water can be considered to be stationary)?
Early mountaineers boiled water to estimate their altitude.If they reach the top and fi nd that water boils at 84 ° C,approximately how high is the mountain?
A pitot-static tube is used for measuring the air velocity, as shown in the figure below. The pitot-static tube is connected to a U- tube manometer containing a liquid of specific gravity SG = 0.9 which indicates a difference of head of H=4 cm of the liquid. What is the air velocity V? The density of water and air is 1000 kg/m³ and 1.2 kg/m³, respectively, and the gravitational acceleration g is 9.81 m/s². 1. [23.51755348, 24.97224751 m/s. V= Air Velocity V Pitot-static probe Liquid of Specific Gravity SG H 9
3. A water tower supplies water through the plumbing in a house. A 3.50-cm-diameter faucet in the house can fill a cylindrical container with a diameter of 44.9 cm and a height of 52.0 cm in 12.0 s. How high above the faucet is the top of the water in the tower? (Assume that the diameter of the tower is so large compared to that of the faucet that the water at the top of the tower does not move.) m
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?
Q.3 A differential manometer is used to measure pressure difference between two fluid systems. Two parallel pipes carrying freshwater and seawater are connected to each other by a double u-tube differential manometer as shown in figure. Determine pressure difference between the two pipelines if h= 32cm. Also if the pressure difference between the pipes is doubled, what will be the difference in heights(h) of mercury?Take density of sea water at that location to be 1035kg/m3 and the specific gravity of the oil is 0.72. Assume all fluids are incompressible.
Q3: A cylindrical tank of radius R=1.5 m and height H = 3 m initially filled with water. At the bottom of the tank there is a hole of radiusr = 20 cm, through which water drains under the influence of gravity. Find the depth of water at tim e 30 second, and determine how long it takes the tank to drain completely?
The figure below shows a rectangular tank of dimensions ho = 2.5 m and b = 2 m is filled to the brim with a liquid of specific gravity 1.1 (tank is 1 m into plane of figure). The tank is subjected to a horizontal acceleration ax, and 30% of the liquid spills over. Determine the difference in liquid pressures at the lower left-hand corner (Point E) and lower right-hand corner of the tank (Point F). PE-PF= 1. [15.70090597, 16.672095597 Free surface ho Liquid X b Liquid at rest ➡ho kPa. 9 Free surface Liquid b ax Under constant acceleration
Q2) The figure below represents a hydraulic car jack has an output cylinder 30 cm in diameter and an input cylinder 5 cm in diameter and is filled with oil of density 900 kg/m 3. An automobile of mass 1200 kg needs to be clevated 35 cm. (a) How far does the piston of the input eylinder need to move? (b) What is the magnitude of the force on the input piston required to keep the car elevated? Input end 4,4, = A4, Output end up by a distance h, area A mass 14 initial initial position position area A Points (a) and down by a distance h, (b) are at the thị same level. fluid of density p,
A Closed tank of water with Length, I = 20 ft Height, h = 10.45 ft %3D Width, w = 5.6 ft Pgage = 0 kPa at the top before acceleration is accelerating at an angle of 38° with respect to the horizontal, where the x component of the acceleration is parallel to that of the length of the tank at a rate of 6.35 ft/s² . If the tank is 76% %3D full, calculate the pressure at the bottom of the left side of the tank and the force acting at the top of the tank during acceleration. Take note that the tank is fixed such that it remains parallel to the horizontal during acceleration