A tank (contains a fluid of density=1239.6 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in the supporting cable. 6 m/s 35 deg -D= 4 m- Do = 4 cm Cable

A tank (contains a fluid of density=1239.6 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in the supporting cable. 6 m/s 35 deg -D= 4 m- Do = 4 cm Cable

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Water flowing in a horizontal pipe is at a pressure of 1.40 x 10^5 Pa at a point where its cross…

Q: The front and side views of a centrifugal impeller are shown in the figure below. All symbols have…

A: The outer radius of the impeller = r2 =0.4 m d2 = 0.8 m The blade height at impeller outlet b2 =…

Q: Momentum Equation Q1: What force components F, Fy are required to hold the block box in figure (1)…

Q: Situation 7: A schematic of a garden fountain is given in the figure. A pump located beneath a water…

A: Given: Volume flow rate is 250 gpm. The garden fountain is shown below:

Q: 1. A pipe bends through an angle of 90° in the vertical plane. At the inlet it has a cross-…

A: 1) Draw diagram of bend pipe

Q: The sprinkler system is used for watering the garden as given figure below. Working fluid enters the…

Q: 2 Q2 = 10 liter/s %3D 3 DI =? Water D3 = 65mm Tank base area=1 m²

A: In the tank, some pipes are inlets and some are outlets. From inlet the water enters within the tank…

Q: A certain fan delivers 340 m3/min of air at a static pressure of 25.4 mm of water gage when…

A: Given Data: Volumetric flow rate, Q1=340 m3/min Static pressure head, h1=25.4 mm of water

Q: The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m . ; blades are…

A: Given, D = 0.5 m N = 1200 RPM Flow Velocity at Exit, Vf2 = 5 m/sec For Blade Velocity, u u =…

Q: A tank (contains a fluid of density=2370.7 kg/m3) stands on a frictionless cart (The cart is fixed)…

Q: 5. A nozzle that discharges a 60-mm-diameter water jet into the air is on the right end of a…

A: To determine:the magnitude and direction of the resultant axial force.Given:The outlet diameter of…

Q: A reducing bend has a linear velocity at section 1. See Figure 4. The flow is uniform at sections 2…

Q: For the sprinkler shown, find a. the torque required to hold it steady, and b. the rotation rate in…

Q: A centrifugal pump with radial inlet (alpha4 = 90°) operates with water at a flow of 0.3 m3 /s.…

A: Given data, The water flow rate, Q = 0.3 m3/s The rotor diameter, D = 0.25 m Width of the blade, b =…

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a…

Q: A centrifugal pump having four stages in parallel, delivers 12 kiloliters per minute of liquid…

A: The Answer is below

Q: (Moment-of-momentum) A lawn sprinkler is constructed from pipe with 0.226-in. inside diameter as…

A: d=.226 in=.0188ft r1=r2=5.54 in=.462 ftr=2.77 in =.231 Since diameter is same and mass flow rate is…

Q: The sprinkler system is used for watering the garden as given figure below. Working fluid enters the…

Q: 4. A tank is full of water and open at the top as shown in the figure. There is a frictionless…

Q: A centrifugal pump having four stages in parallel delivers 12 kiloLiters per minute of liquid…

Q: A pump delivers Q= 13.19 m3/s against a head of 14 m with a speed of 2000 rpm. Find the specific…

Q: A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from…

A: Given:Px=pressure at surface=0Vx=velocity at free surface=0A=0.01 m2zx=2 m

Q: 5.1 An open, 500 mm diameter tank contains water to a depth of 900 mm when at rest. If the tank is…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: 18 |A vertical jet of water impinges on a horizontal disk as shown. The disk assembly mass is 30 kg.…

A: Given mass of thde disk m=30kgU=5m/sh=3mV=15m/sA=0.005m2

Q: P= 2 bar to 2) D;= 0.2 m 25 ° D2 = 0.1 m %3D

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a…

A: Weight = 200 N Thickness = 3 mm velocity = 2 m/s density = 1000 kg/m3 Find tension in the cable

Q: A centrifugal pump impeller delivers 4000 gal/min ofwater at 20 ° C with a shaft rotation rate of…

A: Given, Temperature (T) = 20 °C Q = 4000 gal/min N = 1750 rpm r1 = 6 in r2 = 14 in b1 = b2 = 1.75 in…

Q: A centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down…

A: Given Density = 1000 kg/m³ Head, h = 10 m Speed, N = 2900 rpm Find Flow rate

Q: For the cart in the figure shown, compute the force on the wheels caused by deflecting the jet and…

Q: 5. In this a fire fight system of ship water has speed N m/s. hose is in equilibrium Calculate the…

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a the ocean…

Q: The impeller of a centrifugal pump is of 25 cm diameter and 5 cm width at the periphery. It has…

A: In this question only one part is given so I am going to solve part one of the given question. By…

Q: Homework Question: The pipe bend as in the figure below has D1 = 29 cm and D2 = 12 cm. When water at…

Q: A static thrust stands as it showed in the Figure. The intake velocity is 200 m/s, exhaust velocity…

A: Given data:- The intake velocity = 200 m/s, exhaust velocity=500 m/s, intake cross-section area =1…

Q: A centrifugal pump has r2 = 9 in, b2 = 2 in, and β2 = 35°and rotates at 1060 r/min. If it generates…

A: Given: Centrifugal pump rotates at N=1060 r/min, head generated is h=150 ft calculating the angular…

Q: A tank (contains a fluid of density 2414.5 kg/m3) stands on a frictionless cart (The cart is fixed)…

Q: Q6. A single acting reciprocating pump has a plunger diameter of 10 cm and the stroke of 20 cm. The…

Q: A sharpe-edged orifice has a diameter of 25.4 mm and coefficients of veloc- ity and contraction of…

Q: A tank (contains a fluid of density=2715.2 kg/m3) stands on a frictionless cart (The cart is fixed)…

Q: reducing water pipe section has an inlet diameter of 50 mm and exit diameter of 30 mm. If the steady…

A: Given Data D1=50 mm D2=30 mm V1=2.5 m/s

Q: A Pelton wheel has a mean bucket speed of 15 m/s with a jet of water impinging with a velocity of 40…

A: Given data, Speed of bucket Discharge R=density=Angle of deflection ,Now, Velocity of jet And, And ,

Q: The plunger diameter of a single acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A: Given: The diameter of the plunger is: D=115 mm=0.115 m The length of the stroke is: L=2r=230…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A tank (contains a fluid of density=1239.6 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a
jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in
the supporting cable.
6 m/s
35 deg
-D= 4 m-
Do = 4 cm
Cable

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 Ib/ft'. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for mercury equal to 846 and for water equal to 0 62.4 at 68° F. Mercury
While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at ahead of 75 ft. If the impeller diameter is 1.5 ft. and the blade width is 1.75 in.,find the (a) blade angle β2, (b) radial velocity Vr2, and (c) blade speed u2. Assumeno whirl at the inlet.Ans: β2=12.5°; Vr2=8.1 ft./s; u2=70.7 ft./s
points A and B are given as 29.43 N/cm2 and 22.563 N/cm respectively while the datum head at A and 266 Fluid Mechanies Problem 6.7 A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures c B are 28 m and 30 m. Find the loss of head between A and B.
Q6: The U-bend in the figure below is connected to a flow system by flexible hoses that transmit no force. The pipe has an ID of 3 in. Water is flowing through the pipe at a rate of 600 gal/min and density is 1000 kg/m³. The pressure at point 1 to 5 psig and at point 2 is 3 psig. What is the vertical component of the force in the support? Neglect the weight of the pipe and fluid. Flow FIGURE Vertical pipe U-bend. Flex hoses Support
Find the horizontal and vertical forces to hold stationary the nozzle shown in the figure below. The fluid flowing through it is 10 °C liquid water; A₁ = 1.2 m², A₂ = 0.300 m², V₁ = 15 m/s, p2 = Patm and p₁ = Patm + 75 kPa. Neglect effects of gravity. Fx= i Fy= i A1 P1 KN kN Fy ZA A2, P2 = Patm Fx 45° Patm
I need the answer quickly
A centrifugal pump is shown in the figure below. Absolute velocity, V₂ b₂ = 1.0 cm 0₂= 45% w, T Absolute velocity, V₁ b₁ = 3.0 cm R₂ = 0.13 m R₁ = 0.065 m Impeller Calculate the torque required to drive the pump at 30 Hz and to deliver 20 °C water at 4.5 m³/min. T= N.m. 30°=01
Do all the parts
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height the impeller outlet b₂ = 0.02 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.5 m³/s. The outlet blade angle 3₂ = 35 degrees and the impeller rotational speed w=1600 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The gravitational acceleration g = 9.81 m/s². The theoretical (Euler) head is m. Front View P₂1 r2 b2- 118 Side View
Water flows out of 5 mm x 200 mm slots in a sprinkler as shown. The mass flow rate is 15 kg/s. 200 mm 250 mm a. Find the torque required to prevent the sprinkler from rotating. b. Find the rotation rate of the frictionless sprinkler when released.
Q4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁=30cm D₂=20cm 6 Q4 1.5
Example: In a 45° bend a rectangular air duct of 1 m? cross-sectional area is gradually reduced to 0.5 m² area. Find the magnitude and direction of force required to hold the duct in position if the velocity of flow at 1 m? section is 10 m/s, and pressure is 30 kN/m². Take the specific weight of air as 0.0116 kN/m³. Solution: Fay 45° Fzx PA, cos 45° 45° Vzcos 45° 2. 45°