a mulching plant uses a large motor to shred logs into small pieces. It takes the chipper motor 10 seconds to reach operational speed. A conveyor feeds the chipper hopper with large logs. to avoid jams, the chipper motor must be running 10 seconds before any logs are fed in from the conveyor. when the stop pushbutton is pressed, the conveyor immediately stops, but the chipper continues to run for 10 seconds after the conveyor stops (in case a log is still in the chipper). Use start stop pushbuttons to operate the system.

a mulching plant uses a large motor to shred logs into small pieces. It takes the chipper motor 10 seconds to reach operational speed. A conveyor feeds the chipper hopper with large logs. to avoid jams, the chipper motor must be running 10 seconds before any logs are fed in from the conveyor. when the stop pushbutton is pressed, the conveyor immediately stops, but the chipper continues to run for 10 seconds after the conveyor stops (in case a log is still in the chipper). Use start stop pushbuttons to operate the system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

Choice the correct answer
The voltage induced in 8 poles lamp wound generator is 120 V with armature resistance = 0.3 2. What will be the terminal voltage at a load = 3.6 A when the machine is rewound as a wave?
A. The brushes used in a DC generator a) ride against the commutator segments. b) are made from material softer than the commutator segments. c) are generally marked Al and A2 d) all of the above B. A magneto is a DC generator that uses for its pole pieces. a) electromagnets b) permanent magnets c) either "a" or "b" d) neither "a" nor "b"
A 255 V, DC lathe machine, (not a 2 pole machine) has armature resistance and series resistance are 0.150 and 1702 respectively. The motor has 25mWb flux per pole. The ratio of pole to parallel paths is unity. The product of this ratio and number of turns in armature section is 1000. When it runs light, it has a speed of 1200 rpm. If it runs at maximum load, it takes a current of 70A. (1) Which machine is this one, shunt or series ? Is machine lap wound or wave wound? (3) Calculate the no load back EMF. (4) Calculate the no load armature current. (5) Calculate the no load shunt current. (6) Calculate the current drawn by the machine. Calculate the variable losses on load. (8) Calculate the armature power when it runs light. (9) Calculate the stray losses when it runs light. (10) Calculate the full load armature current. (11) (12) (13) Calculate the full load back EMF. Calculate the Variable losses on maximum possible load. Calculate the armature power on maximum load. (14) Calculate…
Question 6 Copper losses represent: O A. Losses due to friction of the moving parts O B. Windage losses O C. None of the other choices are correct O D. Friction losses in the windings of the machine E. Losses due to magnetization and demagnetization of the core
Question#3 For the linear machine of question #2: a. When this machine is operating as a motor, calculate the speed of the bar for loads of 0N to 30N in 5 N steps. Plot the speed of the bar as a function of load. b. Assume that the motor is operation with a 30 N load, and calculate and plot the speed of the bar for magnetic flux densities of 0.3 T to 0.5 Tin 0.05 T steps. c. Assume that the motor is running at no-load conditions with a flux density of 0.5 T. What is the speed of the bar? Now apply a 30 N load to the bar. What is the new speed of the bar? What flux density would be required to restore the loaded bar to the same speed that it had under no-load conditions?
(a) different number of turns (b) same size of copper wire (c) a common magnetic circuit (d) separate magnetic circuits. 10. In a transformer, the leakage flux of each wind- ing is proportional to the current in that winding because (a) Ohm's law applies to magnetic circuits (b) leakage paths do not saturate (c) the two windings are electrically isolated (d) mutual flux is confined to the core. 11. In a two-winding transformer, the e.m.f.per turn in secondary winding is always.........the induced e.m.f. power turn in primary. (a) equal to K times (b) equal to 1/K times (c) equal to (d) greater than. 12. In relation to a transformer, the ratio 20: 1 indi- cates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary. 13. In performing the short circuit test of a trans- former (a) high voltage side is…
What is turnover torque and when occur؟
DC machines
Look carefully at the figure and answer the following questions. For your answers choose between on the right, on the left and it is zero; there are no more options. (a) When the switch is “open” i. Where does the current flow in the battery? ii. Where is the magnetic flux going in the bar on the left? iii. Where does the magnetic flux go in the bar on the right? iv. Where does the current flow in the resistor?
Question 1 Select all that apply. Which of the following are considered to be "core losses"? 12R heating loss Flux lines that bulge out at core gaps Currents that circulate within the machine non-ferrous components Field Lines that circulate around conductors and coils Rapid Changes in Domain orientation
Which of the following statements are true? I-If an alternating current is applied to a winding, an alternating field is produced. II-If a direct current is applied to a winding, a standing (constant) field is formed. III-Rotating field can be obtained using a single winding. IV-If a rotating motor is disconnected from the mains and voltage is applied to the windings, the motor brakes.