A 3- ac motor is connected to 125 Vac lint to neutral 3- 60 Hz from which it draws 22A line current @ 0.7 power factor. (a) What value of Y-connected capacitance will correct the voltage source unity power factor for this motor? (b) What is new current?

A 3- ac motor is connected to 125 Vac lint to neutral 3- 60 Hz from which it draws 22A line current @ 0.7 power factor. (a) What value of Y-connected capacitance will correct the voltage source unity power factor for this motor? (b) What is new current?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical power developed by the motor is ............ (i) 20 W (iii) 500 W (ii) 980 W (iv) 200 W
What will be the operating power factor of a 3-phase induction motor, whose ratings are 230 V, 50 Hz, 120 hp, and 4-poles? Motor is operating at rated conditions with an efficiency of 92% and draws a line current of 260 A. The core loss and stator copper losses are 1710 W and 2830 W respectively. (a) 0.85 (c) 0.93 (b) 0.90 (d) 0.80
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
The winding of a 4-pole alternator having 36 slots and a coil span of 1 to 8 is short-pitched by ........... degrees. 150 40. 90 20 Brushless excitation system consisting of: Stator field winding and power diodes stator and rotor field winding and capacitor stator and rotor field winding and power diodes Everything mentioned in the options Full Name : *
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
Difference between three phase and single phase induction motor... Don't copy from other websites otherwise you will get thumbs down...
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
A three phase 6000 V alternator has the following O.C.C. at normal speed: Field current : 14 18 23 30 43 Terminal voltage: 4000 5000 6000 7000 8000 With armature short circuit and fall load current flowing the field current is 17 A And when the machine is suppling fall-load of 2000KVA at zero-power factor the field current is 42.5 A, and the terminal voltage is 6000 V. Determine the field current that required when the machine is supplying the fall-load current at 0.7 p.f. lagging.
Here it is the equivalent circuit of and induction motor and it is per phase circuit my question is name for me the variable for example R1 is the winding resistance and so an the all variable and please show me a pic of the real machine with the variable for example for R1 happens because of the winding i need to see the winding in the real machine, please help me to understand well
The name plate of single phase induction motor has following data output 373W,230V, frequency 50Hz. Input current 2.9A and power factor is 0.71. Speed 1420 rpm What is efficiency of motor.
Q3 A 50 Hz split-phase induction motor has a resistance of 50 and an inductive reactance of 200 in the main winding as well as starting winding. Determine the value of resistance and capacitance to be added in series with the starting winding to send the same current in each winding with a phase difference of 90°. Ans[ 14.99 Ω, 127.5μF]