Give an outline on the general requirements of installation of devices in an hazardous area, non-compliance with code, define a Hazardous Area and give an example of a Hazard in an industrial location/industry

please answer all questions and give me a sample ansowers 1. What code sets standards for electrical installation work? 2. What authority enforces the requirements set by the NEC? 3. Does the NEC provide minimum or maximum standards? 4. What do the letters “UL” signify? 5. What section of the NEC states that all listed or labeled equipment shall be installed or used in accordance with any instructions included in the listing or labeling? 6. When the word “shall” appears in a NEC reference, it means that it (must)(may) be done. (Underline the correct word.) 7. What is the purpose of the NEC?

State and explain Paschen’s law. How do you account for the minimum voltage for breakdown under a given pd condition?

Centennial College - School of Engineering Technology - Toronto ELECTRONICS SHOP PRACTICES CHAPTER 7: SOLDERING TECHNIQUES 7,5 QUESTIONS 1. Which tools will you need for soldering? 2. What type of solder do we call the Eutectic Solder? 3. If the temperature is too high, the is bellow required, the solder joint will appear cold and silvery and will be of the contact may occur and circuit will not work. If the 4. A long and sharp will be of little use when soldering wires or 5. The iron should have a tip to prevent and should have a wattage rating of to Watts. 6. When soldering, apply heat solder will to both, the component lead and much more readily over the copper pad so that the 7. Keep the soldering iron tip and working surfaces wipe only before using and immediately. 8. Do not solder from a heated tip before off the iron. alternate applying the surface. 9. If tips become and wiping to being used. 10. Periodically. the tip from your tool and with a suitable cleaner for your skills.…

23. The __________  formula relates physical and chemical process rates to temperature and is used to describe the relationship between temperature and time to failure for electronic

36. Electrical explosions directly into the face of a person working on or near energized electrical equipment can and will cause serious injury or death. OSHA laws and NFPA 70E have strict safety requirements for working on electrical equipment. The basic rules are to turn off the power before working on the equipment and to wear the proper type of nonflammable clothing. To further provide safety for the worker, the National Electrical Code has a requirement pertaining to arc-flash hazard warning. This requirement is found in a. 110.16 (A) b. 220.1 of the NEC C. 330.1 d. 410.5

As an electrical and electronic engineer, your manager has asked you to write a report for the attention of new employees, listing and describing the operation of safety devices that are commonly found offices and other industrial situations. The report should include all of the details in the task below.     Task   For the following application, list two electrical safety devices that can be used, and describe their operation:A Star delta starting induction motors

What is the most important rule of electrical safety?

Ohm's Law states that the electric current flowing though a ________ is directly proportional to the ________. Select one: a. closed circuit --- total resistance b. closed circuit --- switch resistance c. open circuit --- supply voltage d. closed circuit --- supply voltage

I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?