A load has impedance, Z = (110 + j27) 2. Convert this value of Z into polar form, |Z|Z8, where |Z| and 0 are the modulus and argument of Z, respectively. /Satu beban mempunyai galangan, Z = (110 + j27) 2. Tukarkan nilai Z ini ke dalam bentuk 'polar', \Z|ZO, di mana |Z] dan 0 adalah masing-masing 'modulus' dan 'argument' Z.]

A load has impedance, Z = (110 + j27) 2. Convert this value of Z into polar form, |Z|Z8, where |Z| and 0 are the modulus and argument of Z, respectively. /Satu beban mempunyai galangan, Z = (110 + j27) 2. Tukarkan nilai Z ini ke dalam bentuk 'polar', \Z|ZO, di mana |Z] dan 0 adalah masing-masing 'modulus' dan 'argument' Z.]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Use Millman’s theorem and determine the magnitude of the neutral displacement voltage,(Vsn) in the phasor form. Use Millman’s theorem and determine the phase voltage (Vbs) of the load in polar form. Use Millman’s theorem and determine the phase voltage (Vbs) of the load in polar form. Use Millman’s theorem and determine the current,(Ib) in phase b of the load in phasor form. Use Millman’s theorem and determine the current,(Ib) in phase b of the load in phasor form. Use Millman’s theorem and determine the reading on the wattmeter connected in line B of the circuit.
a) total impedance [ZT] in polar form, b) current [ I ] in phasor form, c) resistor voltage [VR] in phasor form, d) power factor [p.f.] indicating whether leading or lagging
consider the following diagram of impedances in per unit of a common base a) get the YBUS admittance array and the ZBuz impedance array 213-j2 pu zt2-j0.15 zg2-j1.85 791-j0.9 211-0.1 1 212-j0.5pu 223-j0.5pu Va 1 p.u. Jv1-1p.u. 22-10 pu
Two SGs are supplying a load by Pwad with 0.9 PF lagging. Gi has a no-load frequency of 54H2, and a slope Spi=1.1MW/Hz. G2 has a no-load frequency of 51HZ, and a slope Spz=1.1MW/Hz. If the system frequency is 50HZ: 1. How much power is supplied by each generator? 2. What is the load power Pload? 3. Draw the house-diagram for this system. 4. Find the system frequency, if the governor set points on G1 are decreased by 1Hz.
Given the circuit below. a A 220°n U,07t 100 -V 3-ø source b 5260°n B 'IcA Iec 22-30°n Determine the phasor line current la in the three-system shown in the figure (both magnitude and angle). Explain why the line current Ic is unaffected by 220°N the impedance. Calculate the phasor line current Ia in the three-system shown in the figure (both magnitude and angle).
Ix |ZL 220° A rms 2 Ix FIGURE 14-31: Circuit schematic for problem 14.15.
The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance calculation is D12=D23=D31=D. Select one: True False
The following single-phase loads are connected to a 415V three-phase supply. Z, = (25 - j15)0, Z, = (45+ j10)2 and Z, = (5+ j30)2. Answer questions 37 and 38. -. What is the current in amperes in the red phase? A. 6.65233.69 D. 5.60233.69 B. 8.23/30.96 C. 14.23430.96 Find the magnitude of the current in the neutral conductor in amperes. A. 18.16 с. 21.33 B. 14.23 D. 12.54 E. 15.68 . A three-phase supply energizes three resistive single-phase loads which draw the following currents: 1, =84, 1, = 6A and I, = 24. What is the magnitude of the neutral current? A. 8 В. 16 С. 5.29 D. 12.49 E. 5.61
10 Ω m I₁ j4 Ω + I₂ ~ Vs E₁ || 2:1 The load on the right is absorbing 650 W -j200 VAR. V₁ = 80 / 0° V. + V₁ I
For a T.L. of Zo=50 Ohm, terminated with ZL= 100 Ohm, the value of the VSWR is: O 2 O 3
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
Element X shown in the three-phase schematic is a pure reactive element. With this element connected, the generator power factor is unity. Indicate:(a) The three-phase real and reactive power of the generator. b) Indicate if X is an inductor bank or a capacitor bank. c) The three-phase reactive power of element X. d) Indicate the reactance per phase of element X, for a star connection. e) If the frequency is 60 Hz, indicate the physical value of the X element.