Column A 1. It is one of the ratings in a device which indicates the amount of watts consumed by the device. 2. It is the force or potential difference that is required to make the current flow in a circuit. 3. A type of current with one direction flow of electric charge. 4. It is the opposition to the flow of electric current. 5. It is the continuous flow of electrons in a circuit. Column B a. voltage b. current c. resistance d. direct current е. power capacitance

Column A 1. It is one of the ratings in a device which indicates the amount of watts consumed by the device. 2. It is the force or potential difference that is required to make the current flow in a circuit. 3. A type of current with one direction flow of electric charge. 4. It is the opposition to the flow of electric current. 5. It is the continuous flow of electrons in a circuit. Column B a. voltage b. current c. resistance d. direct current е. power capacitance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Discuss your observations on both series and parallel circuit. (Brightness of light bulb) 2. Briefly discuss the differences of series and parallel circuit based on current, voltage, and resistance. 3. Do batteries last longer in series or parallel? 4. What is Electricity? 5. How do electrons move from one atom to another? 6. Discuss the difference between direct current and alternating current? 7. What is circuit? 8. What is the purpose of a switch? 9. What do you this is life without electricity?
3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF
1. The practical unit of electric charge. 2. A path for the current to flow. 3. DC Voltage has 4. Resistance to current flow in AC circuits, measured in ohms. 5-7. Types of grounds in electrical circuits. 8. Also known as Ohm's Law Original Formula 9. A quantity defined as amount of work done over time. 10. Types of material that has 4 valence electrons. 11. One Coulomb is equal to 12. Best conductor material type. 13. Best insulator material type. 14.The value of a resistor without considering its tolerance value percentages. polarity electrons or protons stored in a dielectric. 15. 1 picoampere (pA) is equal to ampere (A).
In the following circuit using Kirchhoff's find: a) The current in each branch of the circuit. b) The voltage across each branch. c) State whether each battery is charging or discharging.
What are the differences between load resistance in a circuit and internal resistance in a battery? Explain.
Which of the following statements is true ? OA. Power is additive in series and parallel circuits. O B. A battery is a current source. OC. In a closed circuit, current leaves the positive terminal of a battery, and is used up by the time it reaches the negative terminal. O D. Current only flows through the path of least resistance.
A) Find the equivalent resistor of the circle between points a and b?B) If a constant voltage source (15V) is placed between points a and b, calculate a valueCurrent iS
What are the factors that affects or influence the electrical properties of a material? c) Two of you have been given two instruments with the units in ohms, your colleague measures the resistivity of the material whiles you measure the resistance. Your supervisor comes around and ask you to comment both measurements, what would you tell him?
Q1) What is current in terms of charge? a) Current is measured 2A in a DC circuit * How much charge is involved in the process? * How many electrons are involved in the process? * The voltage source of this current is 12 Volts. What is the power produced by the source?
2. In the figure shown below, determine the following: Battery voltage = 240 volts a. The current in the battery, I. b. The current in the 7-ohm resistor, Resistances are in ohms c. The current in the R-ohm resistor, y. d. The current in the 18-ohm resistor, I e. The current in the R-ohm resistor, I,. I2 7 42 I5 I3 12 R I4 18
2 What is the equivalent of 1 Farad into ratio? Select one: a. 1 Volt per Joule b. 1 Volt per Coulomb c. 1 Joule per Volt d. 1 Coulomb per Volt
Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The internal resistances are 0.004, 0.005, 0.003 and 0.0025 ohm. Calculate for parallel connections: (a) internal emf and resistance of the single equivalent cell (b) current for a terminal voltage of 1.95 volts, (c)current in each cell