Please solve the problem with a neat paper sheet. The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch.

Q: a b c d h   82 mm     139 mm     39 mm     18 mm     33 mm   Clamps like the one shown are commonly…

A:

Q: 6. Way 28 mm diameter steel and 20 mm A composite beam made of aluminum rods in diameter. Elasticity…

A:

Q: Lever Problems - effort Resistance and Mechanical Advantage  R = 50 Lbs Length FE = .75 inch…

A: GivenR=50lbsFE=0.75inFR=12in

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: Determine the precise location of the critical stress element at the cross section at A The precise…

A: Given data:The part is loaded at point B with  in the negative y direction, at point C with  in the…

Q: A 21-mm-diameter steel [E = 206 GPa; a = 12.5x10-6/°C] bolt is used to connect two rigid parts of an…

A: Given-Information:- d =21 mmE = 206 GPaα = 12.5 ×10-6/°Ca = 120 mmT1 = 23°CT2 = 54°CP = 2.4 kN…

Q: If P is to be 400 N. What is the value of the weight W? В A

A:

Q: TA 500 Ib buoy, with a 2 ft radius is tied to the bed of a lake using a steel cable. What is the…

A: Mass of the buoy = 500 lb Need to determine the tensile force in the cable.

Q: In order to find the force in DJ we will have to make a new cut. Cut through IJ, DJ, and CD. The…

A:

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: 300N forces on the pliers? 300N What forces are exerted on the bolt at E in the figure below as a…

A: Given: Force on the pliers, Fp = 300 N Required: Fb ( force exerted on the bolt at E )

Q: A pair of pliers grips the bolt as shown below. 30 mm X₁ B 70 mm X₂ Note: tan 0=y₁/x₂ (a) For the…

A: (a) Draw the free-body diagram of each parts of the pair of pliers.

Q: In a set of pulleys, 3 in the top, 2 in the bottom, it is required to lift a load. If 23% of the…

A:

Q: The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one…

A: Given data:find:The maximum force

Q: A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the bolt.…

A: Given data: The torque required to break the bolt is T = 105 ft-lb. The length of the wrench is l =…

Q: 140 N 80 30 + 26 mm 39 mm - 1. Find the magnitude of force "F" and, 2. the magnitude of the…

A:

Q: A 200 m tape weighing 35 N is suspended between the two ends under a standard pull of 176 N. The…

A:

Q: Determine the diameter, in inches, of a circular steel rod that could withstand a tensile force of…

A:

Q: Determine the force in members AB, BC, and CE of the crane shown in Figure 3-1.

A:

Q: find the tensile of the bolt with diameter 38mm,80kN

A:

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: If the load applied at the handle, P = 45 N, calculate the force that results on the piece held in…

A: Given That P FBD

Q: A 1000 Ibs TTTTT t A horizontal cable exerts a force of 399.971 pounds while holding a boom into…

A:

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: B. what is the type of force in each one of the figures below depending on the contact? 2 00. Fpash…

A: Types of Forces acted at different Kinds.

Q: The connection shown consist of five steel plates joined by a steel bolt with a diameter of 6 mm.…

A: The given information in the problem is shown in the following attached image:

Q: Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all…

A: Given data, A 80 k downward force is acting in a junction of bar A and B. To determine:- The…

Q: The total length of a first class lever is 9.0 ft. This is used to move a load of 390 lbs, as…

A:

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: Question 4 Part A If 0 = 27° and F = 5 kN , determine the magnitude of the resultant force acting on…

A: Given -

Q: Two helical coil springs are made from a steel bar radius of 20 mm. One spring has an outer and…

A:

Q: In the Figure 6, the absolute force value in the bar AC is (in kN): Figure 6: 5 m/ 5 m 5 m A 20 KN B

A:

Q: For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft.…

A: Given: The screw base diameter, d = 21.5 mm The load need to compress, F = 1218 kgf Nut surface…

Q: 1. A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the…

A: Given: The breaking torque is 105 lb-ft. Linear density of the cheater bar is 6.6 lb/ft. The bar is…

Q: You are designing a 1/4 inch diameter pin with a yield strength of 50,000 psi to hold 1000 lbf. You…

A: In case of tension and double shear the failure will be at the same time. Generally, the yield…

Q: Group E c- Use the method of joints to determine the force in member CD d- Use the method of…

A:

Q: Sketch a free-body diagram of each element in the figure. Compute the magnitude and direction of…

A: To sketch: The free body diagram of each element and compute the magnitude and direction of each…

Q: For the clamping device shown calculate the force in Member BE if F=133, A=288, and B=322. Also…

A: The value of P is 102.34N

Q: 3 in axle tire A B lugwrench

A: Given:The length of the lug wrench, The diameter of the wrench, The shear yield stress,

Q: Knowing that the central portion of the link BD has dimensions 3mm x 30 mm made of steel with…

A: