A cylinder-piston system contains air. The initial volume of the system is 0.1m3, the pressure 101kPa, and the piston touches a spring. The system is heated and the volume is doubled from the original while the pressure is 300kPa. Assuming that the spring force is proportional to displacement (a) Show the process on a p - v diagram (b) Calculate the specific work in process.

A cylinder-piston system contains air. The initial volume of the system is 0.1m3, the pressure 101kPa, and the piston touches a spring. The system is heated and the volume is doubled from the original while the pressure is 300kPa. Assuming that the spring force is proportional to displacement (a) Show the process on a p - v diagram (b) Calculate the specific work in process.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is ¼ time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k
There is 3.5 L saturated liquid water at 175 kPa pressure in the frictionless moving piston-cylinder system shown in the figure. The heat given to the system is 500 kJ and the electrical work is 1320 kJ. Since half of the water evaporates at constant pressure; a) Write the energy balance equation (First Law), b) Calculate the mass (kg) of water, c) Calculate the required shaft work (kW), d) Show the process in T-v and P-v diagrams, including saturated liquid and saturated vapor curves
A gas is compressed from an initial volume of 0.38 m3to a final volume of 0.1m3. The variation of pressure with respect to the volume is given by the following equation p = aV + b, where a=-1200KPa/m3 and b = 600KPa/m3. Find the work done in this process.
QI/ the cylinder contains 0.2 kg a refrigerant R-134a of saturated water liquid at 20 °C. The stops location corresponds to 50% of the initial volume. The water is heated to the final state at 50 °C. If the piston reaches the stops? and what are the initial and final pressure. R-134 a
Q3: A. The frictionless piston shown in Figure below has a mass of 20 kg. Heat is added until the temperature reaches 400°C. If the initial quality is 20 percent, find (a) the initial pressure, (b) the mass of water and (c) the work done on the piston. 30 mm Piston Watcr vapor 50 mm 100 mm
For the cylinder below, the final volume inside cylinder (V3) in (Liter) ;is A frictionless piston-cylinder device initially contains 0.2 kg of steam at 400 kPa, 300 °C. Now the steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 135 °C. |frictionless Piston /// / Steam ,m=8-2 kg Pi= 400 kPa Ti= 300°C (sat. lig.)2 T3 = 135 C stops Below 0.1 O Between 0.1 and 0.2 O Between 0.2 and 0.3 Above 0.3 O
In a reciprocating air compressor, high pressure air in the cylinder pushes the piston against theexternal load and expand to a lower pressure. In a test the following measurements were noted:Internal energy of air before expansion = 27 kJInternal energy of air after expansion = 8 kJHeat entering the cylinder during the process = 2 kJFind the work output from the expansion process.
Need help with this book problem using thermodynamics Nitrogen gas at constant pipeline conditions of 200 kPa and 300 K passes slowly through a valve into a well-insulated, frictionless, and initially evacuated piston-cylinder assembly. A pressure of 150 kPa in the cylinder is needed to support the piston due to its own weight and the ambient atmosphere. The volume under the piston is 1 m3 at the end of the process. Find (a) the boundary work done during this process, (b) the final temperature of the nitrogen in the cylinder, and (c) the mass that enters the cylinder during the process.
A piston and cylinder device contains 0.15 kg of water at 25◦C (state 1). As shown in the figure, the piston weighs 500 N and has a cross-sectional area of 0.01 m2. Atmospheric pressure is 100 kPa. Heat is transferred to the cylinder from a reservoir at 200◦C, raising the piston. When the piston touches the stops, the volume inside the cylinder is Vmax= 0.165 m^3 (state 2). Heat continues to be transferred until the control mass reaches the boundary temperature (state 3). Determine: a) The initial pressure of the water (kPa) b) The temperature (Celsius) when the piston hits the stops c) The total work (kJ) d) The total heat transfer (kJ) e) The total entropy production for the entire process (kJ/K)
One kilogram of air is compressed from a volume of 1.0 m and a pressure of 100 kPa to a volume of 0.147 m and a pressure of 1000 kPa. Assuming that the compression follows the law pu" the work done during the compression process. = constant, find
Water at P1 = 200 kPa with a quality of 25% has its temperature raised 20 oC (T2 = T1+20 0C) in a constant pressure process. What is the initial (v1) and final (v2) specific volumes?
Refrigerant 134a is stored inside an uninsulated ridged tank and heated by an electric resistor for 5 minutes. The temp goes from -10 degrees Celsius to 40 degrees Celsius. The refrigerant has a quality of .8 and the tank has a volume of .01m^3. The electrical resistor is powered by a 12V battery with a current of 5 amps. How much energy is lost from the refrigerant through the tank walls during this process.