A large pipe, called a penstock in a hydraulic work, is 1.5 m in diameter. It is composed of wooden stave bound together by steel hoops, each 300 mm2 in cross-section. It is used to conduct water from reservo to a powerhouse. If the maximum tensile stress in the hoops is 130 MPa, what is the maximum spacin between hoops under a head of water of 30m? servoir Powerhouse htake Generator Penstock Turbine

Q: The tank shown in Figure (1) is made from plates have 5 mm thickness and allowable stress of D 90…

A: Given data: Plate thickness, t=5 mm  Allowable stress=90 MPa or N//mm2  Internal pressure= 1 MPa or…

Q: A large pipe, called a penstock in a hydraulic work, is 1.5 m in diameter. It is composed of wooden…

A:

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 49 KN if it…

A: Determination of Outer diameter of Tubular Rod##

Q: The figure shows a system of 3 steel wire, each with an area 0.05 in? , used to lift a load W=1,500…

A:

Q: A large pipe, called a penstock in a hydraulic work, is 1.5 m in diameter. It is composed of wooden…

A:

Q: 03 A solid steel shaft 120 mm diameter and 1.5 m long is used to transmit power from one pulley to…

A: Solid shaft diameter = 120 mm Length of solid shaft = 1.5 m Maximum allowable shear stress = 50 Mpa…

Q: 17.6 A solid steel shaft 3 in. in diameter and 4 ft long is fixed at one end and free at the other,…

A: Given data  Diameter of shaft =3 in  Length of shaft = 4 ft  Axial tensile force = 50000 Lb

Q: In the figure below, a solid shaft with a diameter of 50 mm is subjected to the torques applied to…

A:

Q: A solid 2.1 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: 2) Consider a cylindrical vessel that is subjected to both an internal pressure p and an applied…

A:

Q: A solid shaft of 30 mm in diameter has a rated output of 20 kW. If it powers the shaft at 12 Hz,…

A:

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A: Springs- Springs are elastic member which undergoes deflection when loaded and regains its original…

Q: The assembly of pipes consists of galvanized steel pipe AB and BC connected together at B using a…

A: Given data: Length of pipe (AB)1=1m Inner Diameter=17 mm Outer diameter=20 mm   Length of pipe(BC)…

Q: Q3: A plan of building's structural members is shown in the figure below, a bearing concrete wall…

A:

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A:

Q: Consider the overhanging beam shown in the figure below. (Figure 1) Figure ▼ Part A 8 kN/m Tmax= 4 m…

A: An overhanging beam with uniformly distributed load and a point load at the free end.Overall height…

Q: The solid shaft is subjected to the following loads. Determine the diameter d of the shaft to the…

A: Determine the diameter d of the shaft to the nearest mm

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A: The shear stress developed in the hollow shaft is  ζ = TZp T - Torsional moment  Zp - Polar…

Q: 1-34. The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of…

A:

Q: Please calculate the stresses at points A, B, C and D for the given problem in the above figure.

A: under the effect of pure bending the maximum permissible stress is  under the effect of the pure…

Q: Question 4. A hollow steel tube 5 m long with external and internal diameters 100 mm and 80 mm…

A: To determine the buckling load and the safe load for the given tube [to be used as a column].…

Q: homogeneous 10 m rigid bar has a mass of 800 kg and is suspended at both ends by a 4 m bronze cable…

A: SOLID MECHANICS:

Q: Q.1 A solid circular shaft transmits a power of 100 kW at 1500 rpm. For a limiting shear stress of…

A: Power transmitted by shaft, P =100 kW Rotation of shaft,                 N = 1500 rpm Limiting shear…

Q: Consider the rig set up in the figure above. This shows a force being applied to a hollow square…

A:

Q: Question 2 Calculate the maximum value of force G shown in Figure Q.2, if the diameter of cach rod…

A: Diameter of bar = 5 mm Permissible stress = 180 Mpa L1 = 2900 mm L2 = 2200 mm L3 = 2600 mm a =360 mm…

Q: a 3 m long cantilever beam (i.e., a beam fixed at one end) that carries a 500 kg concentrated point…

A: Tensile stress is 132.21 MpaCompressive stress is 257.465 MpaExplanation:Step 1:Step 2:

Q: Question-fluid. Water is flowing through a pipe of 40cm diameter with friction factor equal to 0.06…

A: Water is flowing through a pipe of 40 cm diameter- d=0.40 m, Friction factor f= 0.06, At a distance…

Q: Problem 5. A thin cylindrical vessel contains a fluid at an internal pressure of 2 N/mm?. If the…

A:

Q: Q2: The solid rod shown in the Figure has a radius of (20 mm). If it is subjected to the forces of…

A:

Q: What is the power transmitted by a 100 mm diameter solid shaft at 150 rpm without exceeding a…

A: Given- Dia d=100 mm,Speed N=150 RPM,Maximum stress=60 N/mm2,π2=10, It is needed to find the Power P.

Q: The torsional assembly shown in the figure consists of a solid 60-mm diameter aluminum [G = 28 GPa]…

A: Given data  TB = 9 KNm TC = 9KNm GBr = 45 GPA GAl = 28 GPA

Q: Two solid circular cross-section bars, one titanium and the other steel, each in the form of a…

A: For Steel, Diameter at free end, D1 = 50mm Diameter at joint, D2 = 70mm. Modulus of elasticity, Es =…

Q: QUESTION 4 A composite spring has two closed coiled springs connected in series, each spring has 12…

A:

Q: For the bar shown, calculate: 50 kN Ø40 mm a) The axial stress and strain due to uniaxial loading b)…

A: Given data : Tensile load (P)=50 KNDiameter (ϕ)=40 mmLength (L)=2 mPoisson ratio ν=0.3Modulus of…

Q: A 4m long rectangular sectioned rigid solid pole with 30mm thickness is fixed to a wall in one end…

A:

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.