2) Consider a cylindrical vessel that is subjected to both an internal pressure p and an applied torque Tat the ends (as shown). Using Mohr's circle, find the principal stresses and maximum shear stress in the wall of the tank. Assume an inner cylinder radius r = 25 inches, wall thickness t = 1 inch, applied torque T = 1500 kips-in and internal pressure p = 30 psi. [Ans. to Check op1-981.8 psi] P T T

2) Consider a cylindrical vessel that is subjected to both an internal pressure p and an applied torque Tat the ends (as shown). Using Mohr's circle, find the principal stresses and maximum shear stress in the wall of the tank. Assume an inner cylinder radius r = 25 inches, wall thickness t = 1 inch, applied torque T = 1500 kips-in and internal pressure p = 30 psi. [Ans. to Check op1-981.8 psi] P T T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part A The solid aluminum shaft has a diameter of 60 mm. Set T = 1810 N-m. (Figure 1) Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate units. HA ? (Tabs )max = Value Units Submit Request Answer Figure 1 of 1 E Provide Feedback 300 N•m 600 N m T, 900 N•m
1a) Figure Q1a shows two tubes made of the same material which are riveted together by 50 rivets of 5mm diameter pitched uniformly. The left tube is fixed at section A and the right tube is subjected to an axial tensile force of 20kN. The thickness of both tubes is 5mm. The inner diameter of the right tube is 180mm. Take E-100GPa. Determine, the normal stress in each tube and shear stress in each rivet. the axial tip displacement at section B. Assume the rivets are rigid. the total strain energy stored. () i) iii) Figure Q1a 200mm 1m. Rivet 190mm 1m. B 180mm F=20KN
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4m. If the tank is designed to withstand a pressure of 3 MPa, a. Determine the required minimum thickness of the cylindrical and hemispherical shells b. Determine the minimum required number of bolts for each hemispherical caps. Figure 4
HOME WORK 3- Combined For the assembly shown in the figure below, Determine the state of stress at point A on the cross section of the pipe at section a-a. 20 mm Section -a P=200N a=280mm b=180mm d=26mm
(4) Two kids (200 N each) are balanced on a seesaw. Plane a-a (containing Point A) is just left of the pin support. Plane b-b (containing Point B) is just right of the pin support. Illustrate the combined state of stress at Point A and at Point B on the two stress cubes below. (Yes, compute values, of course.) Ans. 214 kPa 1.2m 1.2m Point A (on plane a-a): x y ^y 4 200 N A SEESAW GIVEN: Iy= 2.488 E6 mm 4 I₂0.9338 E6 mm 4 12 14 14 12 N 12 ib 33 лу 33 x 2000 Points A&B dims. in mm Point B (on plane b-b): ^y ------ NA x ----- N
A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the figure. For bronze, G = 35 GPa and for steel G = 83 GPa. Determine the maximum shearing stress developed in each segment. Solid Shaft STEEL A Tc = 290 N-m 25 mm Ø -1 m Solid Shaft BRONZE 40 mm Ø -2 m Td = 550 N-m Required Values: (Units in MPa) Tst1= Thr=. Tst2 Hollow Shaft STEEL -2.5 m B D-60 mm d=50 mm For segment DB
A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 22 mm. Compute the maximum stress in the bar Use E = 230 GPa. Answer must be in MPa.
Cylindrical rod is placed inside. fube of the same length. a the ends of the rod and tube are attached to a rigid support one side and A vigid plate on the other the load on the rod - tube assembly is increased from zero to 26 KN and removed. Draw load-deflection diagram & calculate a the residual stresses in rod & tube Rod Tube Tube 2 A₁ = 46.4mm² Er = 200 Gpa A₁ = 64.5 mm P 100 Gpa = мра ра - 246 MPa 3y = 300 MPa engineering Rod Tube K 800. mm A
Brass ninum Problem 2 Two 10-kN forces are applied to a 20 x 60-mm rectangular bar as shown. Determine the stress at point A when (a) b = 0, (b) b = 10 mm, (c) b = 25 mm. 10 mm 10 mm 30 mm 10 kN 30 mm 10 kN 25 mm
The post shown, whose cross-sectional area is 100 x 150 mm2, rests at the middle of a circular solid steel plate. The steel plate is placed above a hollow cylinder. Both the steel plate and the cylinder have diameter of 300 mm and a thickness of 20 mm. Solve for the following: a. punching shear stress in the steel plate b. punching shear stress in the hollow cylinder c. bearing stress in the steel plate due to the post d. bearing stress in the cylinder due to the steel plate
A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld