Q3: A plan of building's structural members is shown in the figure below, a bearing concrete wall connecting four columns on a raft foundation, the raft foundation is resting on a soil having a unit weight of (17.5) kN/m', the loads is explained in the table below. Find the stress at the center of the building at a depth equal to (2)m Units kPa Structural member Raft footing Concrete wall Column Loads 220 620 kPa/m 2240 kN 2m 4m 10m

Q3: A plan of building's structural members is shown in the figure below, a bearing concrete wall connecting four columns on a raft foundation, the raft foundation is resting on a soil having a unit weight of (17.5) kN/m', the loads is explained in the table below. Find the stress at the center of the building at a depth equal to (2)m Units kPa Structural member Raft footing Concrete wall Column Loads 220 620 kPa/m 2240 kN 2m 4m 10m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem The composite bar system in Figure 4.8 consists of a steel bar and a bronze bar that are both securely attached to a rigid block and rigid supports. The system is loaded with a total load P at the rigid block. If the total applied load P=42000 lb, determine the stresses in the two bars. 6′ S TE FIGURE 1.48 Composite bar system for Problem 12. Steel bar } Rigid block -} Bronze bar E₂ = 30 x 10º psi A₂ = 1 in² E-15 x 10 psi Ag-4 in²
Assuming that no tensile stress can occur between the reinforced concrete dam body and the ground, the dimensions of which are given in the figure, calculate the height h at which the water body can safely rise for the pressure safety stress obem=4 MPa in the ground and plot the normal stress distribution for this case. The unit volume weights of concrete and water are pb=24 kN/m³ and ps=10 kN/m³, respectively. (Calculations will be made for unit length.) 30m 16m 6m TII C
A beam with varying load is shown at the figure below. If the beam properties are given, what is the final stress at bottom of the beam at midspan where total losses of the prestressing force is 27% (MPa) Properties: Beam width = 290 mm Beam height = 463 mm Varying load = 19.6 kN/m Span of the beam 10 m Prestressing force = 481 kN %3D eccentricity = 126 mm Wo (kN/m)
A cantilever beam, 100 mm wide by 270 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 80 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
3): For the figure shown below. Determine the normal and shear stresses on the plane AB. On what plane does the maximum shear stress exist. 40 kPa 20 kPa 20 kPa 80 kPa 20 kPa 420 kPv 80 KP 40 kPa
A cantilever beam, 90 mm wide by 280 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1300 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
answer the following
A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at top of the beam section at midspan where the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 263 mm Beam height = 455 mm Uniform load = 6.9 kN/m Span of the beam = 12 m Prestressing force = 359 kN eccentricity = 115 mm
A The beam with a cross section shown below carries the given loading. Calculate the maximum shearing stress and maximum bending stress developed in the beam W = 35 kN/m 160 kN 5 m 2.5 m B 20 mm 20 mm 80 mm 20 mm 80 mm 120 mm
Exercise 2.8.3. Determine the maximum and minimum stress intensities set up in steel flat section 150 mm wide and 20 mm thick subjected to a pull of 200 kN, which is off the geometrical axis by 4 mm in the plane which bisects the thickness.
For the composite cross-section shown in Figure 2 which is built up out of steel and concrete and issubjected to amoment about Z axis (M), draw the stress profile. Given: Steel E = 200 GPa Concrete E = 25 GPa M = 8616 in kN.m
A cantilever beam, 80 mm wide by 220 mm high and 7 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 90 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.