A Im wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is 0.04. Uniform flow takes place in the channel at a flow depth of 0.5. At a particular section gradually varied flow GVF is observed and the flow depth is measured as 0.6m. The GVF profile at that section is classified as

A Im wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is 0.04. Uniform flow takes place in the channel at a flow depth of 0.5. At a particular section gradually varied flow GVF is observed and the flow depth is measured as 0.6m. The GVF profile at that section is classified as

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 1m wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is 0.04. Uniform flow takes place in the channel at a flow depth of 0.5 m. At a particular section gradually varied flow GVF is observed and the flow depth is measured as 0.6m. The GVF profile at that section is classified as
A 1 m wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is 0.04. Uniform flow takes place in the channel at a flow depth of 0.5 m. At a particular section, gradually varied flow GVF is observed and the flow depth is 0.6 m. Identify and classify the GVF profile at that section.
A rectangular channel with a bottom width of 4.0m and a bottom slope of 0.0008 has a discharge of 1.5m3/sec.In a GVF in this channel,the depth at a certain location is found to be 0.3 m.Assuming n=0.016, determine type of GVF profile.
This is a four-part problem. A trapezoidal channel of 3.5:1 side slope and 4 ft bottom width, discharges a flow of 300 cfs. Use a channel slope is 2% and the Manning coefficient is 0.012. Part A. Determine the flow depth in ft. Part B. Determine the water velocity in fps. Part C. Determine the critical flow depth in ft. Part D. Determine the flow classification.
Qle: A flow rate of 0.4m ^ 3 /sec is to be carried in an open channel at a velocity of 1.5 m/sec. If the channel cross section is trapezoidal with water depth equal to the width of the channel bottom and side slope of 1:1. Manning roughness coefficient is 0.03. Determine: a) The bottom width b) The channel bed slope
A trapezoidal channel with bottom width of 3m and side slope of 1V: 1.5 H carries a discharge of 8.0 m³/sec with the flow depth of 1.5m. The Froude number of the flow is
A trapezoidal open-channel has a bottom width of 30 ft and side slopes of 2:1 (H:V). The channel is paved with a concrete surface. If the channel is laid on a slope of 0.0001 and carries a uniform flow at a depth of 6 ft, determine: a) the discharge (flowrate) in ft3/s. b) the state of the flow (critical, subcritical, super critical)?
For a triangular channel with the horizontal dimension of the side slope is 3 (i.e Z=3), a normal depth 1.82 in ft, and a channel bed slope of 0.088. The channel is lined with concrete with a roughness coefficient 0.014. Calculate the flowrate (Q) in cfs.
Q1 Determine the floew in a long convcrete lined rectangula channel of 12M wide and 40M deep,with a bed slope of 1:400 and with a Manning ,n of 0.016.If the flow is halved,what is its depth. Q2. Determine the flow depth ina long length of lined trapezoid channel of base width 3.5M and side slope of 1:1,when the flow rate is 20m3/s.Manning'n+0.016,assuming the channel can be considered as wide.
A concrete-lined, rectangular channel has to be constructed to carry a discharge of 500 cfs. Design the channel assuming that the following values are fixed based on the design conditions: a. Bed slope = 0.002 b. n = 0.015 c. b/y ratio = 2.0 (i.e., the width, ?, is equal to 2y)
Water in a 6-m-wide rectangular channel flows at a rate of 4 m³/s at a depth of 0.6 m. (a) What is the velocity (m/s) of flow upstream of the hump? (b) Is the flow (0.6 m-depth) super-critical or sub-critical? Compute the Froude number. (c) What is the critical depth, Yc (m)? (d) What should be the height, YH (m), of the hump to be installed if we want critical depth to occur? Yc 0.6 m HUMP Profile of channel YH
A trapezoidal channel with bottom width of 3 m and side slope of IV: 1.5H carries a discharge of 8.0m/sec with the flow depth of 1.5m. The Froude Number of the flow is ?