A-5m as shown in the figure. The L300 has a will load of 12kN, 8kN and 6kN. The distance between 12kN AL300 van is traveling to the right. It will cross a beam that is have a simple span B-12m and an overa 8kN wheel load is 3m and the 12kN and 6kN have a distance of 2.5m. a 32.08 b. 28.1 12AN B 61. Determine the maximum reaction(kN) at the roller support. 35.12 d. 24.88 BAN 62. Determine the maximum shear (kN) at the mid span of the simple span if the 12kN wheel load is at that point & 16.5 b. 8.25 e. 10.25 d. 20.5 63. Determine the maximum moment (kN-m) in the simple span. a 60.2 b. 50.2 c. 52.1 d. 58.4

A-5m as shown in the figure. The L300 has a will load of 12kN, 8kN and 6kN. The distance between 12kN AL300 van is traveling to the right. It will cross a beam that is have a simple span B-12m and an overa 8kN wheel load is 3m and the 12kN and 6kN have a distance of 2.5m. a 32.08 b. 28.1 12AN B 61. Determine the maximum reaction(kN) at the roller support. 35.12 d. 24.88 BAN 62. Determine the maximum shear (kN) at the mid span of the simple span if the 12kN wheel load is at that point & 16.5 b. 8.25 e. 10.25 d. 20.5 63. Determine the maximum moment (kN-m) in the simple span. a 60.2 b. 50.2 c. 52.1 d. 58.4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A car weighing 4000 lb, with a wheel base of 9 ft. carries 1900 lb of its load on the front wheels. Compute the maximum moment, in Ib-ft when crossing a 14-ft span.
Four wheel loads rolls as a unit across a 18 span. The loads are 50kn, 30kn, 20kn and 10kn separated respectively by distances of 1m, 3m and 6m. Compute the maximum shear in kn
For the floor plan shown below draw the load diagrams for beam B1 and girder G1 that will be used for designing for moment. Also draw load diagrams for B1 and G1 that will be used for designing for deflection. Neglect self weight for B1 and G1. Note that L/240 deflection limit for total service loads appy. D = 100 psf L = 120 psf
l9
A two span continuous beam having equal spans each of length L is subjected to a uniformly distributed load w per unit length. The beam has constant flexural rigidity. The bending moment at the middle support is
Problem 2 G, Given: 0.75 m 10.4 m D 2 m Mass of car: 1400 kg 4 m- 2 m- 1.5 m- 1.25 m Mass of trailer: 800 kg Braking force at C (µc= 0.40) is applied and causes skid. PIN G, 0.75 m 0.4 m FREE TO ROLL -FREE TO ROLL 2 m- 4.5 m -- 2 m- m-- 1.25 m Determine the reactions at B, C, and D.
A simply supported W36x210 is 20 feet in length and laterally supported at the two ends only. It has a concentrated load of 250 kips at its mid-span. You can ignore beam self-weight.a. Compute Cb.b. Next, compute Cb if the beam is braced at the midspan.
A designer wants to use 2L8x4x7/16 (LLBB) with no gusset plate for beam supports. The moment of inertia about x-x axis will be?
Two C310 x 45 channels are latticed together so they have equal moments of inertia about the principal axes. Determine the minimum length of a column having this section, assuming pinned ends. E 200 GPa. and a proportional limit of 240 MPa. What safe load will the column carry for a length of 12 m with a factor of safety of 2.5?
For the following floor plan, determine the required flexural strength of interior girder C-D on column line 3, using LRFD only if the floor is used for office space. In addition, you can assume a girder self-weight of 300lb/ft, a uniform dead load of 10 PSF (excluding floor weight) and a 5-inch thick reinforced concrete floor.
Please answer asap. Thank you I will like