(a) hot water outlets of diameter 20mm. All outlets are connected to a single main line pipe running down the service stack shaft. After factoring all friction losses and the gravitational head, the system is pressurised such that the ideal flow rate per outlet is 14 l/min. What is the ideal main pipe diameter An open domestic hot water circuit for a residence is to cater for three bathrooms each having two size if the fluid velocity in the main line pipe and the outlet branches is to be kept the same and A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets (i) installed) of 0.5 is assumed (half of the taps open at any point in time) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 0.75 is assumed (ii) (iii) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 1.0 is assumed (All taps open at any point in time)

(a) hot water outlets of diameter 20mm. All outlets are connected to a single main line pipe running down the service stack shaft. After factoring all friction losses and the gravitational head, the system is pressurised such that the ideal flow rate per outlet is 14 l/min. What is the ideal main pipe diameter An open domestic hot water circuit for a residence is to cater for three bathrooms each having two size if the fluid velocity in the main line pipe and the outlet branches is to be kept the same and A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets (i) installed) of 0.5 is assumed (half of the taps open at any point in time) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 0.75 is assumed (ii) (iii) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 1.0 is assumed (All taps open at any point in time)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3b
As shown in the figure, the water flows from the ground floor of a three-storey house to the second floor through pipes of 20 mm diameter (average roughness of the pipe material = 0.0015 mm) at a volumetric flow rate of 0.75 L / s. Water is discharged from the system to atmospheric pressure through a tap with a 12 mm diameter outlet. There are 4 winged elbows, one ball valve and one faucet throughout the installation. Calculate the effective pressure at point 1. (psu=998 kg/m3, usu=1.12x10-3 Pa s, g=9.81 m/s2)
Task 1 The Data: - Clearance volume of 70 cm3, the bore of cylinder is 130 mm, the stroke of compressor is 70 mm, the measured low and high pressures are 120 and 700 kPa, respectively, the volume before and after compression are 900 and 250 cm3, respectively. 1. Determine the volumetric efficiency of a reciprocating compressor 2. Calculate the isothermal and polytropic work of a reciprocating compressor 3. Evaluate the isothermal efficiency
Problem 2 A pump is needed in a water supply system. The water is being pumped out of a ground-level storage reservoir with water surface elevation of 149.27 ft and needs to pass over a hill 2 miles away, where the pipe centerline is at elevation 200.00 ft. The flowrate is 22 mgd, pipe diameter is 24 inches, Hazen-Williams friction factor is 110, and pressure at the crest of the hill must be at least 20 psi. (a) What head must the pump provide? (b) How much power will be added to the water? (c) What size motor should be purchased if the pump/motor combination has an efficiency of 80 percent?
Water in a constant diameter pipe is at 15m on the inlet the pipe leads to the tank situated at a height of 10m, if the total head losses are 8m and the pip inlet and outlet are exposed to the environment and the mass flow remains constant; Chose one of the following: A. no pump is required to ensure water flows to the tank B. none of the above C. a pump needs to ensure water flows to the tank D. the water will flow through gravity to the tank
The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
What is the minimum duct size needed to move 200 cu ft per minute andmaintain duct velocity below 800 feet per minute?
Example -5.2- It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d. pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow and the power to be supplied to the pump assuming n = 0.5 Q (m³/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0
For the hydraulic system of Figure 8, the following data are given: The pump is adding2.984kW to the fluid.(a) Pump flow is 0.00158 m3(b) The pipe inside diameter is 0.0254m.(c) The specific gravity of the oil is 0.9.(d) The oil tank is vented to the atmosphere.(e) The head loss HL between station 1 and 2 is 12.19m.(f) The elevation difference between stations 1 and 2 is 6.096m.Find the pressure available at the inlet to the hydraulic motor(station 2).
As shown in Fig. 4.33, the pipe diameter is d = 25 mm. l1 = 8 m; l2 = 1 m;H = 5 m. The nozzle diameter is d0 = 10 mm, and the minor loss coefficientsof inlet and elbow are f1 = 0.5 and f2 = 0.1 respectively. For nozzle, f3 =0.1 (relative to the outflow velocity of nozzle). The friction factor is k = 0:03.Try to determine jet height h.
3. A pump steadily circulates oil used for lubricating heavy machine tools. The volume flow rate and temperature of the oil are 300 gal/min and 104°F, respectively. At 104°F, the kinematic viscosity and the specific gravity of the oil are 2.15 x 10-3 ft² /s and 0.89, respectively. The pipe lengths are 25 ft for the 4-in diameter pipe and 75 ft for the 3-in diameter one. The Schedule-40 steel pipe has an average roughness element size of 0.0018 in. If all minor losses can be ignored, evaluate how much power (in a unit of horsepower) the pump delivers to the oil. 6 ft 22 ft Flow 15 ft Discharge line 3-in Schedule 40 Suction line 4-in Schedule 40 steel pipe steel pipe Pump
A two branch duct system of circular duct is shown below. The fittings have the following equivalent lengthof straight duct upstream to branch 4m elbow 2m. There is negligible pressure loss in the straight throughsection of the branch. The designer slects 3m/s as the air velocity in all branch sections.What diameter in ft should be selected in the 5 m branch section? A. 2.136 B. 0.340 C. 0.651 D. 1.050