An engine cooling system consists of the following components and associated losses; Engine Block and Head, HL=12.2m Radiator, HL=15.3m 5 x Elbows, C=1.3 3 x Junctions, C_=1.2 3 Meters of piping, C = 9.5 x 10-3, Diameter = 40mm Given that the flow rate of coolant through the cooling system is 50L/min determine the total head loss associated with the system. Take the density of water to be 1000kg/m3 and g = 9.81 m/s?. Select one: Oa. 31.79m O b. 29.79m O c. 27.79m O d. 25.79m

An engine cooling system consists of the following components and associated losses; Engine Block and Head, HL=12.2m Radiator, HL=15.3m 5 x Elbows, C=1.3 3 x Junctions, C_=1.2 3 Meters of piping, C = 9.5 x 10-3, Diameter = 40mm Given that the flow rate of coolant through the cooling system is 50L/min determine the total head loss associated with the system. Take the density of water to be 1000kg/m3 and g = 9.81 m/s?. Select one: Oa. 31.79m O b. 29.79m O c. 27.79m O d. 25.79m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Do not type, it should only be handwritten.
please write clearly if handwritten so that I could read and understand the solutions and steps taken
Figure 8.18 shows a system used to spray polluted water into the air to increase the water's oxygen content and to cause volatile solvents in the water to vaporize. The pressure at point B just ahead of the nozzle must be 25.0 psig for proper nozzle performance. The pressure at point A (the pump inlet) is -3.50 psig. The volume flow rate is 0.50 ft/s. The dynamic viscosity of the fluid is 4.0 x 105 lbs/ft². The specific gravity of the fluid is 1.026. Compute the power delivered by the pump to the fluid, considering friction energy loss in the discharge line.
Oil (y = 48lbf /ft°, p = 2 x 105 Ibf x s/ft2 and Pv = 1.9 PSI) is pumped into the system showing a speed of 4.6 ft/s. The atmospheric pressure is 14.7 PSI. The manufacturer provides the following data for a centrifugal pump operating at its maximum efficiency point: rotational speed of 3000 RPM, flow rate of 0.17 ft/s, NPSH of 150 ft, and dimensionless specific velocity of 0.48. Determine if the pump described has the necessary head to be installed in the system shown (ɛ/D = 0.001) when a 1750 RPM motor is available to drive it. Neglect larger losses after the pump.
The friction loss in laminar flow can be calculated using ____________ A. P.K Swammee and A.K. Jain Equation B. Darcy's equation C. Hazen-Williams Equation D. Hagen-Poiseuille equation
1/2 Determine the Pressure drop in Mpa through a flow control valve that has a capacity coefficient 5 Ipm/Kpa" with flow rate 0.0015 3 m'/sec and the fluid is hydraulic oil with specific gravity 0.85 Select one: O a. 572 Mpa O b. 5.720 Mpa O c. 275 Mpa O d. 0.275 Mpa
Example -5.2- It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d. pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow and the power to be supplied to the pump assuming n = 0.5 Q (m³/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0
Discuss the relation between the head pressure and flow rate for the benefits of connecting the pumps in series?
2. Common Fluids Conversions - Please calculate the following: a. 50 GPM to ft/s in a 4" Sch 40 pipe b. 15 GPM to lbm/s of Chloroform at 25°C 30 psi to ft lb-/lbm of Water at 50°C 40 ft lbf/lbm to hp of a fluid moving at 150 lbm/min. Reynolds number for 100% Glycerol at 75°C flowing through a 2.5" Sch 80 pipe at 10 lbm/s d. e.
A duct system layout is shown in the figure below, it is supplied with air from a central air conditioning unit. The ducts require to be rectangular with a maximum height of 10in due to ceiling limitations. Maximum air duct velocities are: main = 1200fpm; branches = 800 fpm. Determine the sizes of the rectangular ducts and the static pressure at the AHU. Use Velocity reduction method. AHU- AIR HANDLING UNIT (CENTRAL AIRCON)
The flow energy of 24 li/min of a fluid passing a boundary to a system is 2 kJ/sec. What is the pressure at this point? а. 100 kPa b. 140.39 psi c. 1, 000 kPa d. 871 kPa