A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 900 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage V b. the average output voltage Volave) c. the average load current lolavel, d. the rms load voltage Volcms), e. the rms load current loma) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrirms) h. the average diode current ID(ave) i. the rms diode current Ipicms), j. the peak inverse voltage PIV of the diode, k. the average output power Polac 1. the DC output power Po(de) m.the frequency fr of the output ripple voltage, n. the input power factor PF.

A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 900 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage V b. the average output voltage Volave) c. the average load current lolavel, d. the rms load voltage Volcms), e. the rms load current loma) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrirms) h. the average diode current ID(ave) i. the rms diode current Ipicms), j. the peak inverse voltage PIV of the diode, k. the average output power Polac 1. the DC output power Po(de) m.the frequency fr of the output ripple voltage, n. the input power factor PF.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110v/11-0-11 V is used with R1-1 Kn. Assume diode as Germanium. a) Find Input Voltage D, Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. eelee
The following three-phase rectifier has a three-phase source of 240 V rms line-to-line, load is a 20-92 resistance in series with a 40-mH inductance. Determine (a) the dc level of the output voltage, (b) the dc and first ac term of the load current, (c) the average and rms current in the diodes, (d) the rms current in the source, and (e) the apparent power from the source. Van + V b₁¹ + 11 Ven + UN VD₁ D₁ + a DA D3 b D6 D5 C D₂ Load Vo
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?