A fluid flowing at a rate of 416.667 liters per minute in a 60-mm internal diameter pipe has an average velocity in meters per second equal to:

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Course is a term associated with feed. Crank is a rotating link of the shaper mechanism.  Travel is…

Q: Find Wi andwe m2

A: Given data: -  The total length of string 1 is l1. The total length of the string 2 is l2. The…

Q: b. Briefly explain the Liquid Penetrant Method. Mention any three applications.

A: Liquid penetration method is a basic low-cost approach for identifying surface defects such as…

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: power it has an efficiency of 37%, but that when it needs to be ramped u down to compensate for the…

A:

Q: is an example of Active Transducer.

A:

Q: A workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the…

A: Given:Angular speed of the work piece, ω=20 rad/sDiameter of the workpiece, d=4 in

Q: 1 COP Nth False True

A: 1.COP=1/thermal efficiency False

Q: Pneumatics Bending Tool Problem: Sheet metal is to be bended on a pneumatically actuated bending…

A: Given : To find : Pneumatic circuit

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: 8.1.14. [Level 2] The rack on the left (Rack A) is moved up at a speed vд. The rack causes the two…

A:

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: The gas turbine cycle consists of four thermodynamic processes as follows: 1-2: Work output from…

Q: I need the complete procedure, that is, where did you find the value of 895

A: How the value 895 came in the formula

Q: grees) answer only ten of the following multi choice questions. 1. In CNC machine tools, the motors…

A: Note: “Since you have posted multiple questions ,we will provide the solution only to the first…

Q: Answer the following questions by referring the given figure: (0.5 material specification + 0.5 mark…

A: Given:

Q: A reheat cycle with two stages of reheating is executed with steam expanding initially from 200 bar…

A:

Q: Explain the diagrame! C. Ca

A: Solution:   In the diagram, Cm is the Moment Coefficient. CL is the Lift Coefficient.

Q: For a particular process, suppose the bottle neck cycle time is 40, and the raw processing time is…

A:

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 289 K and…

A:

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Explain Quick Return Mechanism along with commercial application

A: Generally, a rotary machine (motor) is used to create to-fro motion i.e. the rotational motion is…

Q: I need parts 7, 8, and 9, answered pertaining to the print and instructions.

A: Hello. You have asked to solve question 7, 8 and 9 but, question 7 is not provided in the given…

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: Give 3 example of an application of the Lever Rule.

A: The compositions of the phases present are determined using the lever rule. The lever rule is also…

Q: Q1// A heat engine receives 1000 KJ of thermal energy from a heat source. (60%) of the resulting…

A:

Q: 1. The assembly consists of two sections of galvanized steel pipe connected together using a…

A:

Q: The processing times of the jobs are given belo

A: option c.

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: A Wind Generator with the following data is installed at a wind site. Upward wind velocity: 8.5 m/s…

A:

Q: 9:54 ص DIZVA 46 * In the shown picture, engaging the gears A and C together gives the gear shift…

A: Concept: In given gear box,  1.By engaging gears A and C, the input and output shaft are on same…

Q: Give 2 examples of methods of members

A:

Q: In the AGMA method, one of the basic equations is o=W'K,K,K, (a) Identify this equation (select…

A: Lewis equation is used to design the gears. Lewi’s equation is the method introduced to calculate…

Q: 1. What is the name of the circuit? 2. How many reservoir symbols are shown, and how many reservoirs…

A: As per Bartleby Answering Guidelines we are supposed to give answer first three sub parts of the…

Q: 4. Calculate the heat loss per linear foot from a 10.3 in. nominal pipe (outside diameter=10.75 in.)…

A: Heat transfer in hollow cylinder: q˙= ∆TR Where ∆T →Temperature difference R    → Thermal resistance…

Q: Name: Murtaza Ali Qasim Grop:B1 Q1/ Given, T- 24°c

A:

Q: Calculate the mechanical advantage of the following compound machine.

A:

Q: Task 1: Your first customer asked for an internal combustion engine to use it in a designed car.…

A: Four-stroke Spark Ignition Engine. In a four-stroke engine, the cycle of operations is completed in…

Q: The following was recorded from the chiller at the BYU-Idaho Central Energy Facility. Atmospheric…

A:

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Generally shaping machine has two strokes they are 1. Cutting stroke or forward stroke 2. return…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.